Search results for: 'Wire Rope - Zipline Cable Ferrule - Zinc Plated'

Zipline Cable Ferrule - Zinc Plated, Two ferrules are required for life support and ziplining applications (ACCT Standards). The extra ferrule serves as a backup in case of primary ferrule failure due to defects or improper swaging. A 12 ton crimper/compression tool is required for 1/4" - 1/2" ferrules Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

Our Galvanized Aircraft Zip Lining Cable is made in accordance with Federal Specification RR-W-410D, meeting the dimensional and strength requirements of MIL-W-83420D. Learn More

Zip Line Super Swaged Compacted Cable / Wire Rope - Zip Line Super cable aka Swaged galvanized cable or compacted wire rope is now available! This incredible cable has at least five times the life of ordinary cable, 25% more strength, 10% faster, and runs 50-70% quieter than traditional cable! This is the wire rope to use for a smoth zipline ride.

Learn More

Our Galvanized Aircraft Zip Lining Cable is made in accordance with Federal Specification RR-W-410D, meeting the dimensional and strength requirements of MIL-W-83420D. Learn More

Our Galvanized Aircraft Zip Lining Cable is made in accordance with Federal Specification RR-W-410D, meeting the dimensional and strength requirements of MIL-W-83420D. Learn More

Our Galvanized Aircraft Zip Lining Cable is made in accordance with Federal Specification RR-W-410D, meeting the dimensional and strength requirements of MIL-W-83420D. Learn More

Learn More

Learn More

Cable Clamp: Crosby Wire Rope Clip Learn More

Learn More

The Felco C16 Wire Cutter has a capacity of 5/8 in. diameter and smaller. This is the GO-TO zipline cable cutter in the industry. Felco cutters keep cutting for years longer than other cable cutters. Learn More

Cable Drop Plate, The lower 1" tie-in hole allows easy attachment of a carabiner or quicklinks. Hot dip galvanized for lasting durability. Cable drop plates are great for giant ladders, giant swings, rope climbs, tire crossings or just about any ropes course element Learn More

If you plan to wrap the cable around a tree or post and not use bolt a tree wrap is what you need. Learn More

The RC-800 Wire Rope Cutters are used for cutting 1/16 to 5/8 inch cable. Learn More

The VERTIGO WIRE-LOCK carabiner is designed for use on via ferrata lanyards along with zipline systems and ropes courses. Learn More

atented cable grabs are designed to provide fall protection for workers ascending or descending from a variety of ladders or vertical structures. The stainless steel cable grab is easily removed or repositioned along a cable. If a fall occurs, the cable grab is designed to immediately lock onto the cable and prevent a free fall. Sold with an integrated shock absorber. Users should be familiar with all warnings and instructions and receive training in the proper use of this device. Product Specs: Universal design Auto traveling operation Durable, lightweight stainless steel design Meets applicable OSHA Standards and ANSI requirements. Recommended lifelines 3/8″ diameter stainless steel or galvanized 7×19 aircraft cable (non-lubed) with minimum tensile strength of 8,000 lbs.

MUST be attached to worker’s harness using ANSI rated autolocking carabiner (NOT included)

Learn More

When the zip line wire rope is terminated with a loop, there is a risk that the wire rope can bend too tightly, especially when the loop is connected to a device that spreads the load over a relatively small area. Learn More

Now with the rear clip in D ring. This harness is perfect for High V and Wild Woozy high ropes elements and zipline runs. Learn More

Great for ropes courses, zip line, high elements, and low ropes challenge courses. Cable Clamps, sometimes called cable stops or cable clips, are tools that are used to clamp down on wire rope commonly used in industrial applications as well as in zip lining and ropes course construction. Learn More

Gripple Ropes Course Cable Connector, Learn More

The Felco C112 Cutter features maximum force transmission which applies the maximum leverage at just the right moment. This coupled with Swiss precision blades make this cutter very easy to use. Learn More

Petzl Paw Rigging Plate, Coming in three sizes for different set ups the PAW provides strong and lightweight organization for your rope set up. Learn More

Designed for use on Challenge ropes course/Zip Lining traverses, on cable or rope. Super strong with a 10,000 rating and a sheathed back up bolt. Stainless steel sides make this cable pulley bomb proof. Learn More

GIANT SWING / SUSPENSION CLAMP FOR 3/8" CABLE

Galvanized Ductile Iron

Learn More

Stainless Steel Cable clamps are ideal for use in salty and acidic environments like zip lining close to oceans or salt lake. These are durable and outlast Drop Forged clamps in harsh environments. Learn More

The Zip Line Evo pulley system is the latest in new ropes course and zip line tailored equipment by Kong. The evolution of our first pulley with integrated connector, that avoids every possibility of mistake. Learn More

Petzl Falcon Rescue/Zipline Harness, The two lateral attachment points transfer the weight evenly around the waistbelt for comfortable surface-supported work/ziplining Learn More

The Finesse climbing/zipline harness is designed specifically for women. It is slightly narrower and lighter than our Silhouette harness, making it a great choice for single pitch or sport climbing applications or even zipline runs. Learn More

These patented barrel springs reduce initial impact by stopping the rider more gradually than traditional springs.

Determining how many springs you will need is easy! Simply take the incoming speed of your rider and for each mph, you need that many springs. (e.g., a 20-MPH zipline needs 20 springs for a 230-lb zipliner). 

All spring systems REQUIRE TESTING to the maximum anticipated speed and load as per ACCT. Can be completed with a minimum of 250 lb. weights, sandbags, or bagged rock salt.

These Zipline  Brakes install in minutes, NOT hours.

Made in the USA.

Each spring array includes a bumper at the beginning for trolley strikes.

Learn More

PetzlAVAO SIT Zipline/Work harness, With a ventral attachment point that distributes the load between the waistbelt and the leg loops during suspended work Learn More

Symmetrical heavy duty oval in hardened zinc plated steel. Larger size and better gate clearance than traditional oval carabiners. Keylock, catch free, gate system for enhanced safety and function. Learn More

Black anodized aluminum sideplates, 2 3/8" zinc coated steel sheave, bushing, and stainless steel axle. 

MBS	Cable/Rope Capacity	Size	Weight	Efficiency
6000lbs	5/8"	4.375x3.5in	0.75lb	91.4%

 

Learn More

This is a simplified version of the PANDION without a equipment loop for climbing rental programs, zipline programs etc. Learn More