Search results for: 'cable stapl sheave'

Ropes Course Zip Line Staples, Staples are the preferred way access ropes challenge course elements and zip line platforms: easy to install, easy to inspect, and easy to climb. If properly installed, the 8" staples can perform as fall protection anchors Learn More

The Head Rush Impact Trolley Sheave Replacement Kit allows you to replace your Impact Trolley sheave assembly should they wear out or become damaged. Learn More

Cable Clamp: Crosby Wire Rope Clip Learn More

Designed for use on Challenge ropes course/Zip Lining traverses, on cable or rope. Super strong with a 10,000 rating and a sheathed back up bolt. Stainless steel sides make this cable pulley bomb proof. Learn More

Crosby Fist Grip Cable Clamps Learn More

Great for ropes courses, zip line, high elements, and low ropes challenge courses. Cable Clamps, sometimes called cable stops or cable clips, are tools that are used to clamp down on wire rope commonly used in industrial applications as well as in zip lining and ropes course construction. Learn More

Black anodized aluminum sideplates, 2 3/8" zinc coated steel sheave, bushing, and stainless steel axle. 

MBS	Cable/Rope Capacity	Size	Weight	Efficiency
6000lbs	5/8"	4.375x3.5in	0.75lb	91.4%

 

Learn More

Fist Grip Cable Clamp - Import Learn More

The Fat Cat is from a line of proven performers for zip line operations: Robertson Mountaineering. This specialized design works great for the thicker and larger 1/2" - 3/4" cables used more and more by zip line tours and canopy tours. Learn More

Cable Drop Plate, The lower 1" tie-in hole allows easy attachment of a carabiner or quicklinks. Hot dip galvanized for lasting durability. Cable drop plates are great for giant ladders, giant swings, rope climbs, tire crossings or just about any ropes course element Learn More

Gripple Ropes Course Cable Connector, Learn More

Stainless Steel Cable clamps are ideal for use in salty and acidic environments like zip lining close to oceans or salt lake. These are durable and outlast Drop Forged clamps in harsh environments. Learn More

Zipline Cable Ferrule - Zinc Plated, Two ferrules are required for life support and ziplining applications (ACCT Standards). The extra ferrule serves as a backup in case of primary ferrule failure due to defects or improper swaging. A 12 ton crimper/compression tool is required for 1/4" - 1/2" ferrules Learn More

Our Galvanized Aircraft Zip Lining Cable is made in accordance with Federal Specification RR-W-410D, meeting the dimensional and strength requirements of MIL-W-83420D. Learn More

Our Galvanized Aircraft Zip Lining Cable is made in accordance with Federal Specification RR-W-410D, meeting the dimensional and strength requirements of MIL-W-83420D. Learn More

Our Galvanized Aircraft Zip Lining Cable is made in accordance with Federal Specification RR-W-410D, meeting the dimensional and strength requirements of MIL-W-83420D. Learn More

Our Galvanized Aircraft Zip Lining Cable is made in accordance with Federal Specification RR-W-410D, meeting the dimensional and strength requirements of MIL-W-83420D. Learn More

Zip Line Super Swaged Compacted Cable / Wire Rope - Zip Line Super cable aka Swaged galvanized cable or compacted wire rope is now available! This incredible cable has at least five times the life of ordinary cable, 25% more strength, 10% faster, and runs 50-70% quieter than traditional cable! This is the wire rope to use for a smoth zipline ride.

Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

This Cable Spooler is Made of sturdy heavy-duty steel tubing and folds for easy storage and had a tough, durable finish.

• Maximum reel width: 18";
• Height from floor to rod: 13"
• Weight: 7.5lbs;
• Holds: 200lbs.

Learn More

atented cable grabs are designed to provide fall protection for workers ascending or descending from a variety of ladders or vertical structures. The stainless steel cable grab is easily removed or repositioned along a cable. If a fall occurs, the cable grab is designed to immediately lock onto the cable and prevent a free fall. Sold with an integrated shock absorber. Users should be familiar with all warnings and instructions and receive training in the proper use of this device. Product Specs: Universal design Auto traveling operation Durable, lightweight stainless steel design Meets applicable OSHA Standards and ANSI requirements. Recommended lifelines 3/8″ diameter stainless steel or galvanized 7×19 aircraft cable (non-lubed) with minimum tensile strength of 8,000 lbs.

MUST be attached to worker’s harness using ANSI rated autolocking carabiner (NOT included)

Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

The Klein Haven Cable Grip is designed for use when a light, compact grip is desired and where zipline or other cable damage is not a factor. Gripping pressure of the knurled jaw s applied to ¼” of zipline cable area. Learn More

The 1/4, 5/16, and 3/8 Swaging Tools are designed for crimping copper and aluminum oval sleeves and stop sleeves on zip lines, life lines,ropes course elements. Learn More

Trapeze bar designed for use on ropes challenge courses: leap of faith. Our Trapeze Bar is made from 1-1/2" solid high density PVC. Learn More

If you plan to wrap the cable around a tree or post and not use bolt a tree wrap is what you need. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More