Search results for: 'must tactical'

A very popular tactical spec carabiner that meets your requirement for a stealthy carabiner with a minimum weight and size. The nut locks on gate to prevent jamming. Learn More

Air Lift Rescue Vest, The latest in victim extraction and rescue. The Air-Lift Rescue Vest brings together fast donning and rapid extraction for short haul and hoist operations. Learn More

Petzl Falcon Rescue/Zipline Harness, The two lateral attachment points transfer the weight evenly around the waistbelt for comfortable surface-supported work/ziplining Learn More

When closed with a wrench, this aluminum quick link is used to close harnesses that have two attachment points that must be joined with a connector. Learn More

Omni Semi-Circle Carabiner, The half-moon OMNI is used to close harnesses that have two attachment points that must be joined with a connector. Learn More

If the nozzle on your TRUBLUE Auto Belay, zipSTOP Zip Line Brake or QUICKjump Free Fall Device shows signs of wear, you must replace it immediately. Nozzle Clip not included. Learn More

Voltige Chest Harness will also increase your "hang" comfort and keep your body in an upright position in case of a fall. Must use with a Sit Harness. Learn More

Petzl Absorbica Fall Arrest Lanyard. The total length of the fall arrest system including the ABSORBICA must not be greater than 2 meters, as specified in the EN 354 and EN 355 standards Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

The Ballet 8 is one of the smallest and strongest mini 8's available. Equipped with Ears, it will serve as a rescue 8, personal escape device, or a regular rappel 8. Learn More

Lanyards are used for protection on high zip lining, ropes courses, adventure courses, industrial heights and a variety of home applications. These are designed to meet the standards of high ropes course/zip line protection and many industrial requirements. Learn More

Ropes Course Zip Line Staples, Staples are the preferred way access ropes challenge course elements and zip line platforms: easy to install, easy to inspect, and easy to climb. If properly installed, the 8" staples can perform as fall protection anchors Learn More

The Universal Mount is a simple and durable mounting point for auto belays and top rope anchors.

Learn More

Learn More

Zipline Cable Ferrule - Zinc Plated, Two ferrules are required for life support and ziplining applications (ACCT Standards). The extra ferrule serves as a backup in case of primary ferrule failure due to defects or improper swaging. A 12 ton crimper/compression tool is required for 1/4" - 1/2" ferrules Learn More

atented cable grabs are designed to provide fall protection for workers ascending or descending from a variety of ladders or vertical structures. The stainless steel cable grab is easily removed or repositioned along a cable. If a fall occurs, the cable grab is designed to immediately lock onto the cable and prevent a free fall. Sold with an integrated shock absorber. Users should be familiar with all warnings and instructions and receive training in the proper use of this device. Product Specs: Universal design Auto traveling operation Durable, lightweight stainless steel design Meets applicable OSHA Standards and ANSI requirements. Recommended lifelines 3/8″ diameter stainless steel or galvanized 7×19 aircraft cable (non-lubed) with minimum tensile strength of 8,000 lbs.

MUST be attached to worker’s harness using ANSI rated autolocking carabiner (NOT included)

Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Stainless Steel Cable clamps are ideal for use in salty and acidic environments like zip lining close to oceans or salt lake. These are durable and outlast Drop Forged clamps in harsh environments. Learn More

Petzl Shunt Ascender, It locks onto either a single rope or double ropes of the same diameter and holds well on icy and muddy ropes. Learn More

Great for ropes courses, zip line, high elements, and low ropes challenge courses. Cable Clamps, sometimes called cable stops or cable clips, are tools that are used to clamp down on wire rope commonly used in industrial applications as well as in zip lining and ropes course construction. Learn More

Yates Figure Eight Chest Harness, Great for use on zip line operations. Attachment points at waist and between shoulders. Safety attachment at rear of waist. Padded waist belt. Super easy to get on and adjust. Learn More

The Head Rush zipSTOP IR Zip Line Brake is fitted with a braking line that can be replaced easily in the field by the owner using the Replacement Braking Line. Learn More

The zipSTOP Zip Line Brake is fitted with a braking line that can be replaced in the field easily by the owner using the Replacement Braking Line. Learn More

The Impact Trolley Cover Plate Replacement Kit allows you to replace the Cover Plates on your Impact Trolley should they wear, get misplaced or damaged Learn More

Stainless Steel sideplates, two 2" Stainless Steel sheaves, Bearing, and Stainless Steel axle. Learn More

The Head Rush Hook Accessory is designed to keep the Impact Trolley and zipSTOP Brake Trolley attached after impact happens, making for easier rider retrieval. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More