Search results for: 'timber bolts'

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

We offer three different style of pilot auger bits for 1/2" lags for ropes course decks, zip line decks and general deck construction for 1/2" & 5/8" lag bolts Learn More

Petzl's Coudee hanger holds the carabiner perpendicular to the rock face, holding the rope away from the rock. The hanger includes an 8mm bolt. Learn More

CMI Trolley Brake Block, The striking surface is crafted from ultra-high molecular weight polyethylene, noted for it's exceptional wear resistance. Steel hardware and a galvanized eye bolt round out the package Learn More

The Petzl Vrillee hanger is for direct aid. It holds the carabiner parallel to the rock face allowing the rope to run easily through the carabiner. With 8mm bolt Learn More

If you plan to wrap the cable around a tree or post and not use bolt a tree wrap is what you need. Learn More

Detachable Pole and Tree Step, These are the preferred security steps for ropes challenge courses either rin trees or poles. Lag bolt and plate are installed into a ropes course pole or tree. Learn More

Designed for use on Challenge ropes course/Zip Lining traverses, on cable or rope. Super strong with a 10,000 rating and a sheathed back up bolt. Stainless steel sides make this cable pulley bomb proof. Learn More

The Slim Ratcheting Lineman Wrench works on four different square sizes, covering all of the common utility pole hardware. The long handle provides plenty of leverage and a tight ratcheting mechanism increases efficiency. The high visibility yellow socket includes a bolt-through design, enabling use on long bolts. Handle is fully integrated for durability.

Features:

• Ratcheting Wrench features four sizes in one tool (4-in-1)
• 3/4-Inch, 13/16-Inch, 1-Inch and 1-1/8-Inch combination square socket sizes
• Works on most common utility pole hardware, such as lag bolts, C clamps and suspension bolts
• Bolt-through design allows bolts to pass through the socket
• Fully integrated handle for durability and non-slip grip for comfort
• Tether hole to keep it connected when working at height
• Bright yellow socket for easy visibility

Specifications:

Learn More

Just Perfect Pole Steps : JP Step II

 

The JP Step I and JP Step II  are Pole/Tree steps and fall protection anchor in one (think integrated LEAD anchor). Installs with 5/8" x 6" lag in poles and 5/8" x 8" lag in trees for the JP I and II. The JP R uses a Specialty 4" Lag Bolt and plate that comes with it. Supports over 5,000 lbs when properly installed. A great alternative to traditional pole steps and staples.  These pole/tree steps are easily installed (about one minute). They also provide great positive climbing aids for hands, feet, and safety anchors. JP Steps for trees and poles are the best looking and safest integrated step - fall protection anchor for ropes courses, challenge courses, and zip line access.

Learn More

Tennis-shoe friendly and stylish—this set offers variety - includes bolts for outdoor use

Learn More

Gripple Ropes Course Cable Connector, Learn More

Unlike the competition it is assembled using machined axles which may cost more but give the SR-71 zip trolley unparalleled structural integrity. Learn More

Shoulder Eye Screw Lag, Use for connecting hand lines, spiders webs to trees, etc. on challenge courses. Do not use in life support applications. Also used when wrapping cable around a tree. Learn More

1-3/4" Nylon Webbing Ajustable Lanyards are used for protection on high ropes courses, adventure courses, industrial heights and a variety of home applications. Learn More

Steel carabiners are referred in ropes course, zip line, and cable applications. Learn More

These are the basic model with NO snap hooks or Zorber. These are only appropriate for clipping in to protection with some dynamic load absorbing features like rope or fairly slack cable such as a belay cable on a high ropes course or zipline. Learn More

Snap hooks are recommended as they are easier for small hands, more ergonomically friendly and are permanently attached to the lobster claws. Learn More

Using machined axles which may cost more but give the SR-71 Hammer zip line trolley unparalleled structural integrity. Learn More

The Zorber Shock absorbing unit is compact and lightweight. When a 220 pound weight is dropped six feet, the maximum arresting force will be less than 900 pounds. Learn More

These lobster Claws are a unique, non-adjustable set of positioning / safety lanyards designed specifically for program high ropes courses. Learn More

Lanyards are used for protection on high zip lining, ropes courses, adventure courses, industrial heights and a variety of home applications. These are designed to meet the standards of high ropes course/zip line protection and many industrial requirements. Learn More

CIFA: 10286 Klein Tools 809-36 hammer is designed and created to strike through jobsite challenges. Engineered with the professional in mind, each tool is job-matched to fit the task at hand. Features: Designed for pole-line work   Rugged and well-balanced, with the weight to drive lag bolts   Forged, tempered-steel head for use in tight areas   Identical faces with round-crown driving surface and beveled edges

Learn More

The Fat Cat is from a line of proven performers for zip line operations: Robertson Mountaineering. This specialized design works great for the thicker and larger 1/2" - 3/4" cables used more and more by zip line tours and canopy tours. Learn More

Shock absorbing sling designed to reduce peak loads in any climbing system!! Learn More

Trapeze bar designed for use on ropes challenge courses: leap of faith. Our Trapeze Bar is made from 1-1/2" solid high density PVC. Learn More

Stainless steel sideplates, 3" aluminum hard coated sheave, bushing, and stainless steel axle. Learn More

Stainless Steel Cable clamps are ideal for use in salty and acidic environments like zip lining close to oceans or salt lake. These are durable and outlast Drop Forged clamps in harsh environments. Learn More

Great for ropes courses, zip line, high elements, and low ropes challenge courses. Cable Clamps, sometimes called cable stops or cable clips, are tools that are used to clamp down on wire rope commonly used in industrial applications as well as in zip lining and ropes course construction. Learn More

Yellow 8' Guy Marker - Guy Guard Learn More

Klein Tools' Lineman's Wrenches are forged from special bar steel and heat-treated for durability and long life. These wrenches are designed for use on heavy three-bolt guy clamps where clearance is limited. Each end has two different size openings, plus a hole at the larger end for turning-in standard pole steps.

• Forged from special bar steel and heat-treated for long life
• Each end has two different size openings
• Small end has 5/8-Inch and 13/16-Inch openings; large end features 29/32-Inch and 1-3/32-Inch openings
• Hole is provided at larger end for turning-in standard pole steps
• Made in USA
• Wrench is suited for use on the heavy three-bolt guy clamps on which clearance is limited
• Dark blue painted finish

Learn More

Cable Clamp: Crosby Wire Rope Clip Learn More

The Felco C16 Wire Cutter has a capacity of 5/8 in. diameter and smaller. This is the GO-TO zipline cable cutter in the industry. Felco cutters keep cutting for years longer than other cable cutters. Learn More

Just Perfect Pole Steps : JP Steps Removable utility pole and tree steps

Learn More