Search results for: 'foot zip trolley and 370070 500 hold'

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Mailion Rapid Links (aka "Rapides" or "Quick-Links") are steel screw-links designed for fastening lengths of chain together on ropes courses and zip lining. They provide critical connections for trolleys, balay devices, cables and cable hardware on a zip line. Learn More

Catch for PANTIN foot ascender, helps to keep the rope in the device during rope ascents. It is available for PANTIN in right- and left-foot versions. Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

Petzl Basic Ascender, The BASIC is a compact ascender that offers excellent grip for rope ascents. The lower attachment hole is large enough to hold the carabiners for the lanyard and the footloop. Learn More

The adjustable FOOTCORD foot loop is used with an ASCENSION or BASIC rope clamp for rope ascents. Its 100 % Dyneema® construction increases durability. Learn More

CMI RTTROLLEY Rapid Transit ZiplineTrolley, Stainless Steel sideplates, two 2" Stainless sheaves, Bearing, and Stainless Steel axle. Taking from the popularity of their velocity zipline trolley, CMI has launched a 2" wheel version, the RT zipline Trolley. Learn More

Petzl's Coudee hanger holds the carabiner perpendicular to the rock face, holding the rope away from the rock. The hanger includes an 8mm bolt. Learn More

Petzl Pantin Ascender, A big advantage for long rope ascents. With the Pantin Ascender supporting the foot, the body is held in a more upright position thus making the ascent faster and less tiring for the arms. Learn More

The Kong KKR Via Ferrata set comes complete with carabiners, and is simply attached to the harness using a lark's foot Learn More

Ring helps hold the connector in the correct position. Learn More

Yates Big Wall Ladder, Big Wall Ladders offer the simplicity of traditional 1" Etriers with the comfort of 2" Wall Etries. Built in spreader bar insures that steps remain open without causing foot pinching. Learn More

Steel carabiners are referred in ropes course, zip line, and cable applications. Learn More

Holds the connector in place and protects the webbing from abrasion. Available in two sizes. Learn More

The Rope Ladder provides moderately challenging access to high elements or an alternative to staple climbs. Constructed of double lashed hardwood dowels with waxed nylon cord to increase durability. Professional installation required.

 

Cost is by: LINEAR FOOT 

Learn More

The Head Rush Bump Stop is considered a sacrificial part that is designed to wear out over time Learn More

The Petzl Vrillee hanger is for direct aid. It holds the carabiner parallel to the rock face allowing the rope to run easily through the carabiner. With 8mm bolt Learn More

Petzl Shunt Ascender, It locks onto either a single rope or double ropes of the same diameter and holds well on icy and muddy ropes. Learn More

Zip Line LEAP Anchor, A high-strength, multi-purpose anchor that can be used equally well as self-belay anchors on staple climbs or as the ideal termination fitting on belay cables anywhere where the cable load is at 90° to the angle of the bolt Learn More

The Klein Haven Cable Grip is designed for use when a light, compact grip is desired and where zipline or other cable damage is not a factor. Gripping pressure of the knurled jaw s applied to ¼” of zipline cable area. Learn More

Square Curved Washers for nut eye bolts and machine bolts. Galvanized Square washers designed for outdoor use in challenge courses, zip lines and other outdoor applications. Learn More

Petzl Simple Descender, The hand holding the free end of the rope is used to control or stop the descent. In narrow pitches, the Simple Descender has the advantage of being able to follow along the rope on its own, without manipulation. It is for use with ropes from 9 to 12 mm. Learn More

Compact self-braking descender, Lock off and work with minimum gear to tangle. The Petzl Rig is a proven performer for the zip line and ropes course construction industry. Learn More

A simple way to reinforce the proper use of auto belay devices and minimize risk from climbing error.

Learn More

Keep your Head Rush zipSTOP Zip Line Brake looking newer longer with a replacement Side Cover Assembly. This cover is easy to replace in the field—no tools required. Learn More

Originally designed for single rope descents in caving, the Stop has become a standard tool for the rope access worker. The Stop is designed to automatically "stop" the descent when the red handle is not depressed. Learn More

The Guide Bag was developed and designed by professional guides. A waist worn bag with 70' of rope meets the requirements for professional operations and insurance. Learn More

Effectively reduces peak loads on an anchor in rescue and rigging system. Learn More

The zipSTOP Zip Line Brake is fitted with a braking line that can be replaced in the field easily by the owner using the Replacement Braking Line. Learn More