Search results for: 'angl zip curv'

By incorporating a rigid stem on this belay/rappel device, climbers go from full lock-off to whipping out rope in a single, smooth action. No more binding up as the device tries to free itself. The amount of friction can be easily adjusted to suit your particular need. Climbing with fat ropes, a skinny partner or on low-angle slabs? Belay with the U-Grooves and clip into the bottom hole of the XF Forge for less friction. For the ultimate control, wrap that skinny cord around the rigid stem and rappel, figure-8 style.

Learn More

GUY ANCHORS- Helix Ground Anchors, Multiple sizes and capacities allow precise designs for the adventure and zip line industry. There may be one or multiple guywires that can be resisted by one or multiple guy wire anchors, dictated by design and load requirements. Learn More

Nail Chipper Tri-Cut Auger Bits, Typically when drilling a hole for a through bolt as used in ropes course or zip line construction, you will need to drill a hole 1/16" bigger than the bolt you are using. 5/8" bolt requires a 11/16" hole. These are all 18" long bits. 7-1/2" are available by request. Learn More

Via Ferrata set made with 20 mm tubular webbing lanyards with inner elastic and Tango alu alloy connectors with double gate safety system.

Fitted with high strength stitching and an energy absorber housed in a bag with zip for easy inspection.
Conforms to the safety requirements of the new revision of EN 958:2017, which includes a load between 40 and 120 kg.
Total length of the set: min. 85 cm - max. 120 cm.

Learn More

Stainless Steel Thimbles, When the zip line wire rope is terminated with a loop, there is a risk that the wire rope can bend too tightly, especially when the loop is connected to a device that spreads the load over a relatively small area. Learn More

Just Perfect Pole Steps : JP Step II

 

The JP Step I and JP Step II  are Pole/Tree steps and fall protection anchor in one (think integrated LEAD anchor). Installs with 5/8" x 6" lag in poles and 5/8" x 8" lag in trees for the JP I and II. The JP R uses a Specialty 4" Lag Bolt and plate that comes with it. Supports over 5,000 lbs when properly installed. A great alternative to traditional pole steps and staples.  These pole/tree steps are easily installed (about one minute). They also provide great positive climbing aids for hands, feet, and safety anchors. JP Steps for trees and poles are the best looking and safest integrated step - fall protection anchor for ropes courses, challenge courses, and zip line access.

Learn More

The Petzl ID is a self-braking descender with an anti-panic function built in. Learn More

The Head Rush Impact Trolley Sheave Replacement Kit allows you to replace your Impact Trolley sheave assembly should they wear out or become damaged. Learn More

The Impact Surface Replacement Kit allows you to replace the Impact Surface on your Impact Trolley should it wear out or become damaged. Learn More

The Impact Trolley Cover Plate Replacement Kit allows you to replace the Cover Plates on your Impact Trolley should they wear, get misplaced or damaged Learn More

PANJI adventure park/zipline harness is a one size harness covering a very wide range of body sizes. Learn More

AVAO BOD Harnesses, The harness also facilitates carrying and organization of tools with multiple equipment loops and retainers for attaching CARITOOL tool holders and TOOLBAG tool-holder pouches. Learn More

Petzl Pandion Harness, Adjustable leg loops allow size to be adjusted depending on comfort desired or layers of clothing worn and permit the harness to be put on when wearing skis or crampons Learn More

GUY ANCHORS- Helix Ground Anchors : 4" x 3/4" x 54" Learn More

GUY ANCHORS- Helix Ground Anchors : 10" x 1-1/4" x 96" Learn More

GUY ANCHORS- Helix Ground Anchors : 8" x 1" x 66" Learn More

GUY ANCHORS- Helix Ground Anchors : 6" x 3/4" x 66" Learn More

Deep Cut Pole Auger Bits Learn More

Zipline Cable Ferrule - Zinc Plated, Two ferrules are required for life support and ziplining applications (ACCT Standards). The extra ferrule serves as a backup in case of primary ferrule failure due to defects or improper swaging. A 12 ton crimper/compression tool is required for 1/4" - 1/2" ferrules Learn More

Shoulder Eye Screw Lag, Use for connecting hand lines, spiders webs to trees, etc. on challenge courses. Do not use in life support applications. Also used when wrapping cable around a tree. Learn More

Nylon Shock Cord consists of a stranded rubber core covered with braided fiber resulting in an elastic cord with consistent stretch and strength. The durable "bungee type" cord is covered with nylon. Learn More

Used as spacers or supports under screw or bolt heads. Our washers are heat treated galvanized. Learn More

Lock washers are a critical component to through bolts on wood poles. Pole shrinkage mandates the use of double coil lock washers to keep pressure on the nut and bolt to prevent loosening. Learn More

Aspir Adjustable Harness, Its low bulk and large range of adjustability also make it great for mountaineering and glacier travel. A great harness too for via ferrata and adventure parks. Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

Just Perfect Pole Steps : JP Steps Removable utility pole and tree steps. This is the step only. These steps can replace common utility pole steps that have an upturned hook end.

Learn More

The Felco C16 Wire Cutter has a capacity of 5/8 in. diameter and smaller. This is the GO-TO zipline cable cutter in the industry. Felco cutters keep cutting for years longer than other cable cutters. Learn More

Just Perfect Pole Steps : JP Steps Removable utility pole and tree steps

Learn More

This innovative, all-in-one Pulley/Auto belay for fall protection is lightweight and easy to use. Auto belay pulley Locks in either direction (right or left) while climbing up or down. Learn More

Certified according to EN 17109 (class D)! The Smart Belay X is a redesign of our legendary Smart Belay - now with innovative magnetic technology for continuous safety and maximum freedom of movement in your high ropes course. Certified according to EN 17109 (class D).

 

• Quick registration and effective management thanks to RFID technology
• communicating, interconnected pulley carabiners prevent accidental detachment from the safety cable
• safety lock with magnet technology for maximum security and protection against careless use
• intuitive operation even for children
• steel pulleys integrated in the carabiner for use on zip lines replace the double pulley
• PILOT BAR minimizes the risk of strangulation and provides support for difficult elements in the course
• modular system allows the use of different connectors and different lengths of tie-in loops
• quick and easy evacuation made possible by opener or steel carabiner (not included in delivery)
• SBX HOLSTER included

Learn More

Cable Clamp: Crosby Wire Rope Clip Learn More

Gripple Ropes Course Cable Connector, Learn More

Used to support cross timbers for ropes course, challenge course, zip lines and industrial applications. Learn More