Search results for: 'auto zip c42v'

The Head Rush Bump Stop is considered a sacrificial part that is designed to wear out over time Learn More

CMI "Beast" Tour Trolley Pulley, Designed for the fast lane of zip line tours, this trolley features a front bumper, reinforced 'crimped' side bars and forward facing design with drop down handles. Learn More

Deep Cut telephone Pole Auger Bits: 24", Super long 24" Pole Auger Bits for telephone poles, utility poles, treated poles, ropes course and zip line poles. Designed for making deep cuts in utility poles, pressure treated lumber, railroad ties, and wet or frozen lumber. Learn More

Yates Figure Eight Chest Harness, Great for use on zip line operations. Attachment points at waist and between shoulders. Safety attachment at rear of waist. Padded waist belt. Super easy to get on and adjust. Learn More

Nut Eye bolts are the main bolts used in ropes challenge course and zip line construction. Zipline and other cables are terminated to the eye bolt around a thimble to prevent cable deformation at the turn back. Learn More

Snap hooks are recommended as they are easier for small hands, more ergonomically friendly and are permanently attached to the lobster claws. Learn More

Our largest HMS designed for easy belay setup in any situation. The frame’s round bar stock works great with a variety of belay techniques including popular semi-auto locking devices, tube devices, and Munter hitch.

• CE EN12275 Certified
• Weight: 85g
• Strength (major axis): 25kN

Learn More

Nut Eye bolts are the main bolts used in ropes challenge course and zip line construction. Zipline and other cables are terminated to the eye bolt around a thimble to prevent cable deformation at the turn back. Learn More

Lag Screw Lag Bolt - Galvanized, Typically used for LEAP anchors, deck constuction for zip lines and ropes courses. Hot Dipped Galvanized; Hex Head Lag Screw. 5/8" x 6" lags or 5/8" x 8" lags are recommended for Leap/Lead/Bolt hanger anchors where through bolts are not required Learn More

Compact self-braking descender, Lock off and work with minimum gear to tangle. The Petzl Rig is a proven performer for the zip line and ropes course construction industry. Learn More

The Challenge harness is built for group-use activities like ropes courses, indoor and outdoor climbing as well as mountaineering. It is an adjustable unpadded harness with three auto locking buckles. A single visible attachment point, closing of the waist on the right side, and two different leg colors for ease and speed of use.

Learn More

Petzl Am'D Carabiner - Add security to your climbing anchors with the Petzl Am'D Traict Locking Carabiner. Take your pick of Petzl's Screw-Lock, Ball-Lock, or Triact-Lock gate to perfectly match your preference. The Am'D Carabiner also has a snag-free keylock gate to assure it never snags on gear when you're building a solid anchor at the top of the pitch you just climbed. Learn More

GUY ANCHORS- Helix Ground Anchors, Multiple sizes and capacities allow precise designs for the adventure and zip line industry. There may be one or multiple guywires that can be resisted by one or multiple guy wire anchors, dictated by design and load requirements. Learn More

Nail Chipper Tri-Cut Auger Bits, Typically when drilling a hole for a through bolt as used in ropes course or zip line construction, you will need to drill a hole 1/16" bigger than the bolt you are using. 5/8" bolt requires a 11/16" hole. These are all 18" long bits. 7-1/2" are available by request. Learn More

Haul kit for pickoffs, making a releasable anchor, or tensioning a system, thanks to its 4:1 mechanical advantage and excellent efficiency (sheaves with sealed ball bearings). Learn More

Via Ferrata set made with 20 mm tubular webbing lanyards with inner elastic and Tango alu alloy connectors with double gate safety system.

Fitted with high strength stitching and an energy absorber housed in a bag with zip for easy inspection.
Conforms to the safety requirements of the new revision of EN 958:2017, which includes a load between 40 and 120 kg.
Total length of the set: min. 85 cm - max. 120 cm.

Learn More

Stainless Steel Thimbles, When the zip line wire rope is terminated with a loop, there is a risk that the wire rope can bend too tightly, especially when the loop is connected to a device that spreads the load over a relatively small area. Learn More

Just Perfect Pole Steps : JP Step II

 

The JP Step I and JP Step II  are Pole/Tree steps and fall protection anchor in one (think integrated LEAD anchor). Installs with 5/8" x 6" lag in poles and 5/8" x 8" lag in trees for the JP I and II. The JP R uses a Specialty 4" Lag Bolt and plate that comes with it. Supports over 5,000 lbs when properly installed. A great alternative to traditional pole steps and staples.  These pole/tree steps are easily installed (about one minute). They also provide great positive climbing aids for hands, feet, and safety anchors. JP Steps for trees and poles are the best looking and safest integrated step - fall protection anchor for ropes courses, challenge courses, and zip line access.

Learn More

The Head Rush Impact Trolley Sheave Replacement Kit allows you to replace your Impact Trolley sheave assembly should they wear out or become damaged. Learn More

atented cable grabs are designed to provide fall protection for workers ascending or descending from a variety of ladders or vertical structures. The stainless steel cable grab is easily removed or repositioned along a cable. If a fall occurs, the cable grab is designed to immediately lock onto the cable and prevent a free fall. Sold with an integrated shock absorber. Users should be familiar with all warnings and instructions and receive training in the proper use of this device. Product Specs: Universal design Auto traveling operation Durable, lightweight stainless steel design Meets applicable OSHA Standards and ANSI requirements. Recommended lifelines 3/8″ diameter stainless steel or galvanized 7×19 aircraft cable (non-lubed) with minimum tensile strength of 8,000 lbs.

MUST be attached to worker’s harness using ANSI rated autolocking carabiner (NOT included)

Learn More

The Impact Surface Replacement Kit allows you to replace the Impact Surface on your Impact Trolley should it wear out or become damaged. Learn More

RSRP431 R-ALF Rescue Hauler Pulley- 2 Way Auto Locking Approved standards CE 0120 ANSI Z359 :4: 2007

 The R-ALF Pulley is the latest innovation in Accessability, Rescue, Confined Space working and Work Suspension Systems. The R-ALF Pulley has an over-speed brake built in so that the Pulley will lock on and hold when a fall occurs. The load rated Becket Eye on the R-ALF means that it can be used in combination with Prussic Pulleys to create a 3: 1 or 5: 1 Mechanical Advantage System. The unique design of the R-ALF (design patent applied for), means that an internal brake is not required and therefore it is capable of several thousand cycles and many arrests (minimum 12 monthly service intervals apply). Weight (grams) 1200 Weight (ounces) 43 Rope diameter range (mm) Approved 11mm EN1891-A Ropes Only Number of persons 2

Learn More

The Impact Trolley Cover Plate Replacement Kit allows you to replace the Cover Plates on your Impact Trolley should they wear, get misplaced or damaged Learn More

PANJI adventure park/zipline harness is a one size harness covering a very wide range of body sizes. Learn More

AVAO BOD Harnesses, The harness also facilitates carrying and organization of tools with multiple equipment loops and retainers for attaching CARITOOL tool holders and TOOLBAG tool-holder pouches. Learn More

Petzl Pandion Harness, Adjustable leg loops allow size to be adjusted depending on comfort desired or layers of clothing worn and permit the harness to be put on when wearing skis or crampons Learn More

GUY ANCHORS- Helix Ground Anchors : 4" x 3/4" x 54" Learn More

GUY ANCHORS- Helix Ground Anchors : 10" x 1-1/4" x 96" Learn More

GUY ANCHORS- Helix Ground Anchors : 8" x 1" x 66" Learn More

GUY ANCHORS- Helix Ground Anchors : 6" x 3/4" x 66" Learn More

Deep Cut Pole Auger Bits Learn More

Zipline Cable Ferrule - Zinc Plated, Two ferrules are required for life support and ziplining applications (ACCT Standards). The extra ferrule serves as a backup in case of primary ferrule failure due to defects or improper swaging. A 12 ton crimper/compression tool is required for 1/4" - 1/2" ferrules Learn More

Shoulder Eye Screw Lag, Use for connecting hand lines, spiders webs to trees, etc. on challenge courses. Do not use in life support applications. Also used when wrapping cable around a tree. Learn More

EYE NUTS and EYELETS, Eyelets, also known as Bolt Eyes, are used under the head or nut of a bolt. All are compatible with the strength of the bolts used with them. Learn More

Nylon Shock Cord consists of a stranded rubber core covered with braided fiber resulting in an elastic cord with consistent stretch and strength. The durable "bungee type" cord is covered with nylon. Learn More

Used as spacers or supports under screw or bolt heads. Our washers are heat treated galvanized. Learn More