Search results for: 'flat zip trolley and 32cm 56 hous'

Rock Exotica Swivels made the first high-quality swivels back in 1987 with high-efficiency bearings and machined bodies. Great for keeping rope straight and tangle free while you climb or zip line. Learn More

A simple way to reinforce the proper use of auto belay devices and minimize risk from climbing error.

Learn More

The HaulerBiner Compact Rescue Kit is a lightweight, compact and simple to use/deploy device. The HaulerBiner is fully rated for lifting people. The HaulerBiner has three pulley wheels incorporated into each carabiner, creating a compact and lightweight 6:1 or 7:1 (theoretical) mechanical advantage system. The HaulerBiner also has a purpose-designed progress capture cam with, an ‘on/off’ position.  The HaulerBiner utilises purpose-developed 6mm (1/4") rope, for strength and easy handling/best grip.  The kit is supplied in a two-pouch bag, for easy deployment. The HaulerBiner is load rated to 140kg (310lbs) but it has an MBS of at least 16kN/3500lbs tested as a complete system. The length of the system, when fully contracted is only 32cm (12"). EN 12278, EN 567 certifications

Learn More

The Head Rush zipSTOP IR Zip Line Brake is fitted with a braking line that can be replaced easily in the field by the owner using the Replacement Braking Line. Learn More

Commercial grade harness acceptable for use in engineered zip line tours, canopy tours, and aerial adventure/trekking parks Learn More

Deep Cut telephone Pole Auger Bits: 24", Super long 24" Pole Auger Bits for telephone poles, utility poles, treated poles, ropes course and zip line poles. Designed for making deep cuts in utility poles, pressure treated lumber, railroad ties, and wet or frozen lumber. Learn More

Yates Figure Eight Chest Harness, Great for use on zip line operations. Attachment points at waist and between shoulders. Safety attachment at rear of waist. Padded waist belt. Super easy to get on and adjust. Learn More

Nut Eye bolts are the main bolts used in ropes challenge course and zip line construction. Zipline and other cables are terminated to the eye bolt around a thimble to prevent cable deformation at the turn back. Learn More

Nut Eye bolts are the main bolts used in ropes challenge course and zip line construction. Zipline and other cables are terminated to the eye bolt around a thimble to prevent cable deformation at the turn back. Learn More

Lag Screw Lag Bolt - Galvanized, Typically used for LEAP anchors, deck constuction for zip lines and ropes courses. Hot Dipped Galvanized; Hex Head Lag Screw. 5/8" x 6" lags or 5/8" x 8" lags are recommended for Leap/Lead/Bolt hanger anchors where through bolts are not required Learn More

Compact self-braking descender, Lock off and work with minimum gear to tangle. The Petzl Rig is a proven performer for the zip line and ropes course construction industry. Learn More

The Am'D PIN-LOCK asymmetrical aluminum carabiner is designed for use with groups. It secures the connection of the user thanks to its PIN-LOCK system, which can only be opened by the operator with a specific unlocking tool. Learn More

The adjustable leg loops of the LUNA harness make it an ideal piece of equipment for mountaineering, ziplining, and ice climbing. Learn More

GUY ANCHORS- Helix Ground Anchors, Multiple sizes and capacities allow precise designs for the adventure and zip line industry. There may be one or multiple guywires that can be resisted by one or multiple guy wire anchors, dictated by design and load requirements. Learn More

Nail Chipper Tri-Cut Auger Bits, Typically when drilling a hole for a through bolt as used in ropes course or zip line construction, you will need to drill a hole 1/16" bigger than the bolt you are using. 5/8" bolt requires a 11/16" hole. These are all 18" long bits. 7-1/2" are available by request. Learn More

The CORAX is the versatile harness par excellence: easy to use and comfortable, it is designed for rock climbing, mountaineering or via ferrata. Learn More

These patented barrel springs reduce initial impact by stopping the rider more gradually than traditional springs.

Determining how many springs you will need is easy! Simply take the incoming speed of your rider and for each mph, you need that many springs. (e.g., a 20-MPH zipline needs 20 springs for a 230-lb zipliner). 

All spring systems REQUIRE TESTING to the maximum anticipated speed and load as per ACCT. Can be completed with a minimum of 250 lb. weights, sandbags, or bagged rock salt.

These Zipline  Brakes install in minutes, NOT hours.

Made in the USA.

Each spring array includes a bumper at the beginning for trolley strikes.

Learn More

Learn More

A fully adjustable, full body harness for work positioning and fall-arrest. Padded hip belt and leg loops for comfort. Available in Easy Lock buckle or Speed Lock buckles. NFPA version includes Speed Lock buckles and all steel components and attachment points.

Learn More

Adjama Climbing Harness, Lightweight and very flexible, thanks to the Delta System leg loop front panels and small dimension leg buckles. Learn More

The Head Rush quickFLIGHT Free Fall Device gives riders the sensation of a “free fall” while comfortably lowering them to the ground.

Learn More

Stainless Steel Thimbles, When the zip line wire rope is terminated with a loop, there is a risk that the wire rope can bend too tightly, especially when the loop is connected to a device that spreads the load over a relatively small area. Learn More

Just Perfect Pole Steps : JP Step II

 

The JP Step I and JP Step II  are Pole/Tree steps and fall protection anchor in one (think integrated LEAD anchor). Installs with 5/8" x 6" lag in poles and 5/8" x 8" lag in trees for the JP I and II. The JP R uses a Specialty 4" Lag Bolt and plate that comes with it. Supports over 5,000 lbs when properly installed. A great alternative to traditional pole steps and staples.  These pole/tree steps are easily installed (about one minute). They also provide great positive climbing aids for hands, feet, and safety anchors. JP Steps for trees and poles are the best looking and safest integrated step - fall protection anchor for ropes courses, challenge courses, and zip line access.

Learn More

The perfect size for light and tower rescues. Fits ropes from 8mm to 1/2". Features built in safety cam for use in "jigger" or "short haul" systems. Use with CMI micro single or double pulley 3:1 or 4:1 mechanical advantage systems. Features a centered bronze bushing. Strength: 7000 lbs. The CMI Single Micro Hauler is 154 mm. tall, 53 mm wide, and 40 mm. thick and 19 g. Learn More

PANJI adventure park/zipline harness is a one size harness covering a very wide range of body sizes. Learn More

AVAO BOD Harnesses, The harness also facilitates carrying and organization of tools with multiple equipment loops and retainers for attaching CARITOOL tool holders and TOOLBAG tool-holder pouches. Learn More

Petzl Pandion Harness, Adjustable leg loops allow size to be adjusted depending on comfort desired or layers of clothing worn and permit the harness to be put on when wearing skis or crampons Learn More

GUY ANCHORS- Helix Ground Anchors : 4" x 3/4" x 54" Learn More

GUY ANCHORS- Helix Ground Anchors : 10" x 1-1/4" x 96" Learn More

GUY ANCHORS- Helix Ground Anchors : 8" x 1" x 66" Learn More

GUY ANCHORS- Helix Ground Anchors : 6" x 3/4" x 66" Learn More

An auto belay is an automatic belay device that eliminates the need for a human belayer. In the case of the Head Rush TRUBLUE Auto Belay, it uses Head Rush's patented self-regulating braking system, which is enabled by non-contacting magnetic braking technology. Learn More

Deep Cut Pole Auger Bits Learn More

Zipline Cable Ferrule - Zinc Plated, Two ferrules are required for life support and ziplining applications (ACCT Standards). The extra ferrule serves as a backup in case of primary ferrule failure due to defects or improper swaging. A 12 ton crimper/compression tool is required for 1/4" - 1/2" ferrules Learn More

Fully adjustable harness for work positioning withcontinuous adjustable webbing, SPEED buckles, padded wide waist belt, anatomicleg loops and shoulder straps.

• super comfortable wide waist belt padding provides maximum comfort when working at height
• strength webbing on the waist belt is stitched in the way that at normal working situation the body weight is absorbed by the padding only
• reflective strap and printing on the waist belt and a reflective strap on the shoulder padding increase the visibility in dark working conditions (the black version of the harness is not equipped with the reflective elements)
• anatomic leg loops and waist belt are covered with strong PES fabric providing high abrasion resistance
• standard easy lock buckles enable smooth adjustment
• narrowed padding and webbing on the shoulder straps in a neck area enhance comfortable work
• leg loops connection straps made from durable PES webbing for better abrasion resistance
• front and back attachment points for fall arrest according to EN 361 marked with additional “A“ marking
• flat rear attachment point does not bear on users back when carrying backpack or breathing apparatus
• front lower attachment point for descender placement or work positioning according to EN 813
• 2 side attachment points for work positioning according to EN 358
• 4 ergonomic braided gear loops with a bearing capacity of 5 kg
• heavier items up to 35 kg can be attached to the webbing on the waist belt
• additional loops on the waist belt and leg loops with a bearing capacity of 5 kg offer additional space for the gear and better gear organization
• wide elastic band at left shoulder strap for the gear attachment (e.g. transmitter)
• slots at the waist belt for Porter tool holder to carry your industrial tools
• shoulder attachment points for confined space rescue according to EN 1497
• chest ascender smart fixation system (using an additional maillon), works best with Cam Clean
• all steel components finished with E-coating for higher corrosion resistance
• identification and methodical label
• Weight: 177g, 62.68oz
• Max Rated Load: 150 kg
• Certifications: EN 358, EN 361, EN 813, EN 1497, CE 1019

Learn More

Shoulder Eye Screw Lag, Use for connecting hand lines, spiders webs to trees, etc. on challenge courses. Do not use in life support applications. Also used when wrapping cable around a tree. Learn More