Search results for: 'one way beal cabl curv'

Steel cable with aluminum rungs. Can be used in ropes courses, caving, rope access work, or emergency preparedness kits.

• Length 32 feet
• Weight: 3 lbs 4 oz.
• Width: 6"
• Breaking Strength: 1324 lbs.

Learn More

Stainless Steel sideplates, two 2" Stainless Steel sheaves, Bearing, and Stainless Steel axle. Learn More

Can be put on in under 30 seconds!!! Innovative harness for high ropes courses and adventure parks. Its easy-to-use, uncomplicated design means that visitors can put it on/take it off on their own. Learn More

These lobster Claws are a unique, non-adjustable set of positioning / safety lanyards designed specifically for program high ropes courses. Learn More

Brakehawk- Zip Line Hand Brake, No more burning through bulky welding gloves or slamming into a zip line bungee brake that leaves you with a hurting neck Learn More

Unlike the competition it is assembled using machined axles which may cost more but give the SR-71 zip trolley unparalleled structural integrity. Learn More

Stainless Steel Thimbles, When the zip line wire rope is terminated with a loop, there is a risk that the wire rope can bend too tightly, especially when the loop is connected to a device that spreads the load over a relatively small area. Learn More

The CMI Velocity Micro Zipline trolley is a fast zip line trolley that is small and light weight. Stainless steel side plates assure long life and minimal wear. Learn More

PANJI adventure park/zipline harness is a one size harness covering a very wide range of body sizes. Learn More

Hydrobot is a new tool conceived for Hydrobot is a new tool conceived for modern canyoning; can be used both with one or two ropes and it allows an easy changement of the braking under load. Learn More

GUY ANCHORS- Helix Ground Anchors, Multiple sizes and capacities allow precise designs for the adventure and zip line industry. There may be one or multiple guywires that can be resisted by one or multiple guy wire anchors, dictated by design and load requirements. Learn More

With a maximum weight of 165 g, the SIROCCO helmet sets a new standard for lightness. The one-piece construction minimizes helmet weight while retaining excellent impact resistance, due to the mechanical properties of expanded polypropylene (EPP). Learn More

Yates Figure Eight Chest Harness, Great for use on zip line operations. Attachment points at waist and between shoulders. Safety attachment at rear of waist. Padded waist belt. Super easy to get on and adjust. Learn More

Using machined axles which may cost more but give the SR-71 Hammer zip line trolley unparalleled structural integrity. Learn More

CMI "Beast" Tour Trolley Pulley, Designed for the fast lane of zip line tours, this trolley features a front bumper, reinforced 'crimped' side bars and forward facing design with drop down handles. Learn More

The Cadillac is versatile enough to be used on big walls,zip line, but shines brightest on multi pitch and traditional routes. Constructed wide for comfort, the Cadillac incorporates an inner waist belt layer that spreads forces over 2.7 times more area Learn More

It may be small, but don’t underestimate the Head Rush LightSpeed Micro Zip Line Trolley. Learn More

Stainless Steel sideplates, two 2" Stainless Steel sheaves, Bearing, and Stainless Steel axle. Learn More

Ultra-compact and extremely lightweight pulley designed for daily tasks or on-site rescue. Learn More

The Y Tail - Participant Ropes Course Lanyard is manufactured from 1/2" high quality US manufactured PolyDacron 3-strand rope. The lanyard has a loop for girth hitch attachment to the harness and two ANSI rated double-locking snap hooks for connection to the lifeline (belay cable). Lanyards are adjustable from 4' (48") to 6'5" (77").

Learn More

Used as spacers or supports under screw or bolt heads. Our washers are heat treated galvanized. Learn More

Just Perfect Pole Steps : JP Step II

 

The JP Step I and JP Step II  are Pole/Tree steps and fall protection anchor in one (think integrated LEAD anchor). Installs with 5/8" x 6" lag in poles and 5/8" x 8" lag in trees for the JP I and II. The JP R uses a Specialty 4" Lag Bolt and plate that comes with it. Supports over 5,000 lbs when properly installed. A great alternative to traditional pole steps and staples.  These pole/tree steps are easily installed (about one minute). They also provide great positive climbing aids for hands, feet, and safety anchors. JP Steps for trees and poles are the best looking and safest integrated step - fall protection anchor for ropes courses, challenge courses, and zip line access.

Learn More

Knot-passing pulley allows passage of joining knots Large diameter sheave mounted on sealed ball bearings for excellent efficiency. Learn More

Effectively reduces peak loads on an anchor in rescue and rigging system. Learn More

Double sewn zip line tether is the only double zip line tether that meets all standards for ACCT, PRCA for professional zip line and canopy tours. Each tether exceeds the 5,000 lb minimum strength requirement. Learn More

Write, type, or stamp information on the ¾ x 1 inch white area. Clear self-laminating portion wraps around to protect writing. Learn More

The elastic leg loops remain adjusted and offer complete freedom of movement. The DoubleBack Light buckle on the waistbelt ensures quick and easy adjustment. Learn More

The Impact Trolley Cover Plate Replacement Kit allows you to replace the Cover Plates on your Impact Trolley should they wear, get misplaced or damaged Learn More

The 20 g barrier has been broken! The Nineteen G is the lightest carabiner in the world – and makes no compromises on strength. Learn More

The PIRANA descender offers multiple braking options and can be installed on the rope without removing it from the harness. Designed for use with canyoning descent techniques. Learn More

Kong Futura Foot Ascender, the Futura system (hand ascender, chest ascender and foot ascender) will be the most compact SRT hardware available on the market - but it will not be the cheapest! The Futura is here. A radical new approach to climbing ropes. Designed by top cavers for tight places in the most remote areas on earth (or under it). Surprisingly simple the new designs are comfortable to use thanks to the ergonomic grips. Learn More

Petzl ZigZag Prusik The linked rings provide precision and fluidity when moving around. The pulley is mounted on ball bearings to allow the slack to be taken up easily. Learn More

Certified according to EN 17109 (class D)! The Smart Belay X is a redesign of our legendary Smart Belay - now with innovative magnetic technology for continuous safety and maximum freedom of movement in your high ropes course. Certified according to EN 17109 (class D).

 

• Quick registration and effective management thanks to RFID technology
• communicating, interconnected pulley carabiners prevent accidental detachment from the safety cable
• safety lock with magnet technology for maximum security and protection against careless use
• intuitive operation even for children
• steel pulleys integrated in the carabiner for use on zip lines replace the double pulley
• PILOT BAR minimizes the risk of strangulation and provides support for difficult elements in the course
• modular system allows the use of different connectors and different lengths of tie-in loops
• quick and easy evacuation made possible by opener or steel carabiner (not included in delivery)
• SBX HOLSTER included

Learn More

Rock Exotica enForcer Load Cell is a compact aluminum load cell that measures force up to 20 kN. Utilizing two sampling modes, the Enforcer is able to monitor systems, and log drop testing in high resolution. Learn More

The Ascension Ascender by Petzl is the benchmark for handled ascenders and has been refined to provide greater comfort; efficiency, ease of use. Learn More

A proven winner for the ropes course. Double-back buckles on the legs and waist.

One Size Fits Most

Learn More