Carriage Bolt w/Nut & Washer, The square neck under the round head will seat into the hole in the wood to prevent the head from turning. Because they are used with wood, carriage bolts are rarely high strength and virtually always supplied in a standard ASTM A307 specification. Learn More

CONNEXION FIXE Anchor strap, Forged steel D-rings on the ends. The Connexion Fixe anchor strap is the climbers choice for top rope anchor systems. This anchor strap is the best for rock climbing rope systems. Learn More

Rope thimbles protect the rope from wear whenever you have a fixed loop in the end of the rope, whether the rope is tied, spliced, or swaged. Learn More

GUY ANCHORS- Helix Ground Anchors, Multiple sizes and capacities allow precise designs for the adventure and zip line industry. There may be one or multiple guywires that can be resisted by one or multiple guy wire anchors, dictated by design and load requirements. Learn More

EYE NUTS and EYELETS, Eyelets, also known as Bolt Eyes, are used under the head or nut of a bolt. All are compatible with the strength of the bolts used with them. Learn More

Unlike the competition it is assembled using machined axles which may cost more but give the SR-71 zip trolley unparalleled structural integrity. Learn More

Nail Chipper Tri-Cut Auger Bits, Typically when drilling a hole for a through bolt as used in ropes course or zip line construction, you will need to drill a hole 1/16" bigger than the bolt you are using. 5/8" bolt requires a 11/16" hole. These are all 18" long bits. 7-1/2" are available by request. Learn More

Great for ropes courses, zip line, high elements, and low ropes challenge courses. Cable Clamps, sometimes called cable stops or cable clips, are tools that are used to clamp down on wire rope commonly used in industrial applications as well as in zip lining and ropes course construction. Learn More

This self-trailing MIO rope grab grips automatically in the event of a fall and dissipates the energy of the fall by slipping along the rope. When used within OSHA guidelines on approved ropes, the amount of slip is well within the OSHA requirements. This rope grab comes with a lanyard and an ANSI Snap Hook. for use on 1/2" ropes.

 

Learn More

CMI EXPEDITION ASCENDER, The Expedition Ascender is a perfect choice for big wall or mountaineering endeavors. Engineered for comfort, the handle opening is extra wide to accommodate gloved hands. Works with 7mm-12mm ropes. Sold individually. Learn More

The Ballet 8 is one of the smallest and strongest mini 8's available. Equipped with Ears, it will serve as a rescue 8, personal escape device, or a regular rappel 8. Learn More

Lock washers are a critical component to through bolts on wood poles. Pole shrinkage mandates the use of double coil lock washers to keep pressure on the nut and bolt to prevent loosening. Learn More

Peguet Maillon Rapide Delta quick links in plated steel and stainless steel. Bulk packaged.

• 10mm Weight: 153 grams. Strength: 45kN CE

Learn More

Fully adjustable harness for work positioning withcontinuous adjustable webbing, SPEED buckles, padded wide waist belt, anatomicleg loops and shoulder straps.

• super comfortable wide waist belt padding provides maximum comfort when working at height
• strength webbing on the waist belt is stitched in the way that at normal working situation the body weight is absorbed by the padding only
• reflective strap and printing on the waist belt and a reflective strap on the shoulder padding increase the visibility in dark working conditions (the black version of the harness is not equipped with the reflective elements)
• anatomic leg loops and waist belt are covered with strong PES fabric providing high abrasion resistance
• standard easy lock buckles enable smooth adjustment
• narrowed padding and webbing on the shoulder straps in a neck area enhance comfortable work
• leg loops connection straps made from durable PES webbing for better abrasion resistance
• front and back attachment points for fall arrest according to EN 361 marked with additional “A“ marking
• flat rear attachment point does not bear on users back when carrying backpack or breathing apparatus
• front lower attachment point for descender placement or work positioning according to EN 813
• 2 side attachment points for work positioning according to EN 358
• 4 ergonomic braided gear loops with a bearing capacity of 5 kg
• heavier items up to 35 kg can be attached to the webbing on the waist belt
• additional loops on the waist belt and leg loops with a bearing capacity of 5 kg offer additional space for the gear and better gear organization
• wide elastic band at left shoulder strap for the gear attachment (e.g. transmitter)
• slots at the waist belt for Porter tool holder to carry your industrial tools
• shoulder attachment points for confined space rescue according to EN 1497
• chest ascender smart fixation system (using an additional maillon), works best with Cam Clean
• all steel components finished with E-coating for higher corrosion resistance
• identification and methodical label
• Weight: 177g, 62.68oz
• Max Rated Load: 150 kg
• Certifications: EN 358, EN 361, EN 813, EN 1497, CE 1019

Learn More

Deep Cut telephone Pole Auger Bits: 24", Super long 24" Pole Auger Bits for telephone poles, utility poles, treated poles, ropes course and zip line poles. Designed for making deep cuts in utility poles, pressure treated lumber, railroad ties, and wet or frozen lumber. Learn More

Designed for rescue, it is great for portable ropes courses, ski & mountain rescue, tyrolean back ups, rescue kits, Rescue training programs, and hauling up access nets and ladders to challenge courses and climbing towers. Learn More

Compact and light first aid bag with reflective zippers for increased visibility and easy access. The inside is designed with different size compartments and zippered mesh pocket. Velcro attachment loops allow easy and safe attachment to a harness or backpack. Includes an emergency whistle. First Aid contents are not included.

• Size: 13 cm x 10 cm x 5 cm

Learn More

Thimbleye® bolts are forged in two styles, straight and bent at a 45° angle. The broad radius of the eye provides an excellent attachment point to dead-end or guy messenger wire, guy strand or formed wire grips. Learn More

A proven winner for the ropes course. Double-back buckles on the legs and waist.

One Size Fits Most

Learn More

Deep Cut Pole Auger Bits Learn More

High-strength VULCAN carabiners are designed for rescue professionals. With a large gate opening and high strength, these carabiners are ideal for setting multiple anchors where conditions are difficult and weight is not an issue. Learn More

The Rescue Figure 8 is a special figure 8 for rescue situations and fast rappeling.  It has a special shap for multiple rope locking, allows rappeling with heavy loads, has a high strength, and fits a wide range of rope diameters. Available in light alloy or stainlees steel.

• Weight: 154g, 5.43oz (alloy) 451g, 15.9 oz (stainless steel)
• Material: Light alloy or stainless steel
• Strength: 40kN

Learn More

Lag Screw Lag Bolt - Galvanized, Typically used for LEAP anchors, deck constuction for zip lines and ropes courses. Hot Dipped Galvanized; Hex Head Lag Screw. 5/8" x 6" lags or 5/8" x 8" lags are recommended for Leap/Lead/Bolt hanger anchors where through bolts are not required Learn More

Petzl Am'D Carabiner - Add security to your climbing anchors with the Petzl Am'D Traict Locking Carabiner. Take your pick of Petzl's Screw-Lock, Ball-Lock, or Triact-Lock gate to perfectly match your preference. The Am'D Carabiner also has a snag-free keylock gate to assure it never snags on gear when you're building a solid anchor at the top of the pitch you just climbed. Learn More

HIT Lever hoists have a rugged contruction and a cover to protect the gear case and the brake equipment. The drop forged and heat treated alloy hooks are equipped with safety latches to ensure safety at all times. The steel handle rotates 360 degrees for operation in any posistion. The chain is made from high quality alloy steel and has been specially heat treated for high breaking stress and durability. This hoist has been tested 1.5 times its rated capacity.

• Designed for construction and industrial lifting and pulling applications.
• Rugged steel body construction, lightweight, compact and portable.
• Powder coat painted to protect against rust and corrosion.
• High Tensile alloy steel chain is heat treated for safety and low-wear.
• Shock resistant gear case and brake cover.

Learn More

The Slim Ratcheting Lineman Wrench works on four different square sizes, covering all of the common utility pole hardware. The long handle provides plenty of leverage and a tight ratcheting mechanism increases efficiency. The high visibility yellow socket includes a bolt-through design, enabling use on long bolts. Handle is fully integrated for durability.

Features:

• Ratcheting Wrench features four sizes in one tool (4-in-1)
• 3/4-Inch, 13/16-Inch, 1-Inch and 1-1/8-Inch combination square socket sizes
• Works on most common utility pole hardware, such as lag bolts, C clamps and suspension bolts
• Bolt-through design allows bolts to pass through the socket
• Fully integrated handle for durability and non-slip grip for comfort
• Tether hole to keep it connected when working at height
• Bright yellow socket for easy visibility

Specifications:

Learn More

Fist Grip Cable Clamp - Import Learn More

The Petzl ID is a self-braking descender with an anti-panic function built in. Learn More

Compact belay device with assisted braking for lead climbing or top rope. All metal construction with cam and friction components in stainless steel for great durability. The rope exits following the device’s axis to avoid twisting. The BIRDIE can be used with all dynamic single ropes from 8.5mm to 11mm.

• All steel construction
• Compatible with ropes from 8.5mm to 10.5mm
• Weight: 210g 7.4 oz

Learn More

The Felco C16 Wire Cutter has a capacity of 5/8 in. diameter and smaller. This is the GO-TO zipline cable cutter in the industry. Felco cutters keep cutting for years longer than other cable cutters. Learn More

atented cable grabs are designed to provide fall protection for workers ascending or descending from a variety of ladders or vertical structures. The stainless steel cable grab is easily removed or repositioned along a cable. If a fall occurs, the cable grab is designed to immediately lock onto the cable and prevent a free fall. Sold with an integrated shock absorber. Users should be familiar with all warnings and instructions and receive training in the proper use of this device. Product Specs: Universal design Auto traveling operation Durable, lightweight stainless steel design Meets applicable OSHA Standards and ANSI requirements. Recommended lifelines 3/8″ diameter stainless steel or galvanized 7×19 aircraft cable (non-lubed) with minimum tensile strength of 8,000 lbs.

MUST be attached to worker’s harness using ANSI rated autolocking carabiner (NOT included)

Learn More

A great harness for group users such as clubs, schools and camps. A great value in a fully adjustable harness. Easily adjustable harness with a single tie in point.

• Weight: 400 grams
• Number of buckles: 3
• Gear loops: 0
• Single reinforced tie in
• Universal size fits up to 47" waist.
• CE and UIAA Certified

Learn More

Learn More

Snap hooks are recommended as they are easier for small hands, more ergonomically friendly and are permanently attached to the lobster claws. Learn More

This Cable Spooler is Made of sturdy heavy-duty steel tubing and folds for easy storage and had a tough, durable finish.

• Maximum reel width: 18";
• Height from floor to rod: 13"
• Weight: 7.5lbs;
• Holds: 200lbs.

Learn More

Our new Ultrascenders are designed to be the most convenient and easy to use ascenders around. We've added a new ergonomically designed safety mechanism which is integrated into the handle channel for maximum ease of use in those long "over the lip" stretches. Learn More