Search results for: 'string 54 mm v tx rope'

The original Adaptive Ropes Course harness, the ARC allows all participants to experience challenge courses and ziplines, without regard to physical ability. Designed especially for participants with physical challenges, the ARC features a thickly padded, rigid seat, with integrated chest and pelvic harnesses, secure four point attachment system and dorsal head panel, providing a safe, comfortable harness for experiencing modern ropes courses.

*ARC Spreader Bar sold separately*

Learn More

Stainless steel sideplates, 3"aluminum sheave, bushing, and stainless steel axle. 

 

MBS	Rope Capacity	Size	Weight	Efficiency
16000lbs	5/8"	6.5x4.25in	1.35lb	92.1%

Learn More

Stainless steel sideplates, 2" aluminum sheave, needle bearing, and stainless steel axle.

 

MBS	Rope Capacity	Size	Weight	Efficiency
8000lbs	1/2"	5x2.5in	0.5lb	90.6%

Learn More

Black anodized aluminum sideplates, 2 3/8" zinc coated steel sheave, bushing, and stainless steel axle. 

MBS	Cable/Rope Capacity	Size	Weight	Efficiency
6000lbs	5/8"	4.375x3.5in	0.75lb	91.4%

 

Learn More

Just Perfect Pole Steps : JP Step II

 

The JP Step I and JP Step II  are Pole/Tree steps and fall protection anchor in one (think integrated LEAD anchor). Installs with 5/8" x 6" lag in poles and 5/8" x 8" lag in trees for the JP I and II. The JP R uses a Specialty 4" Lag Bolt and plate that comes with it. Supports over 5,000 lbs when properly installed. A great alternative to traditional pole steps and staples.  These pole/tree steps are easily installed (about one minute). They also provide great positive climbing aids for hands, feet, and safety anchors. JP Steps for trees and poles are the best looking and safest integrated step - fall protection anchor for ropes courses, challenge courses, and zip line access.

Learn More

By incorporating a rigid stem on this belay/rappel device, climbers go from full lock-off to whipping out rope in a single, smooth action. No more binding up as the device tries to free itself. The amount of friction can be easily adjusted to suit your particular need. Climbing with fat ropes, a skinny partner or on low-angle slabs? Belay with the U-Grooves and clip into the bottom hole of the XF Forge for less friction. For the ultimate control, wrap that skinny cord around the rigid stem and rappel, figure-8 style.

Learn More

This rainbow para cord is ideal for lazy lines (or haul lines) on ropes courses and climbing walls, as well as general use. Kernmantle construction for high strength and low stretch. 350 lb strength rating. 1/8" (3mm).  Made in the Mexico.

Learn More

This rainbow para cord is ideal for lazy lines (or haul lines) on ropes courses and climbing walls, as well as general use. Kernmantle construction for high strength and low stretch. 350 lb strength rating. 1/8" (3mm).  Made in the Mexico.

Learn More

The SWIVEL OPEN gated swivel features a wide opening and thus can be attached to a range of products (pulleys, lanyards). It reduces the bulk and weight of component systems and solves the twisting and tangling problems of ropes and lanyards. Sealed ball bearings offer excellent performance and reliability.

Learn More

The Challenge harness is built for group-use activities like ropes courses, indoor and outdoor climbing as well as mountaineering. It is an adjustable unpadded harness with three auto locking buckles. A single visible attachment point, closing of the waist on the right side, and two different leg colors for ease and speed of use.

Learn More

 Rescue Swivel helps to eliminate twisting in critical lines due to load rotation. Its 9000lb (40kN) MBS gives you piece of mind when moving the heaviest of loads, and its sealed ball bearing will keep it operating smoothly for years.

*Exceeds tests for national fire protection association standard on fire service life safety rope and system components NFPA 1983-2006 edition.  *Not Certified*

Size: 4 1/4" x 1 3/4"
Weight: 5.6 oz
Breaking Strength: 9,000 pounds

Learn More

The D4 Work/Rescue Descender features a unique and innovative cam action, which offers precise control at slow or fast speeds. The progressive cam works by way of one cam operating inside another cam. The D4 is the only ANSI certified descender on the market today.

• Weight: 655 grams (23 ounces)
• Strength: MBS 16kN (3597lbf)
• For use with single ropes from 10.5 - 11.5mm (7/16")
• Working Load Rating (WLL): 240kg (551lbs.)
• Certifications: CE EN12841, NFPA 1983, ANSI Z359

Learn More

A Super-efficient slicing tool that makes the most of its simple design and sturdy construction, the Vital Zip Knife holds a utility blade which is easily replaced once dull with a quick release of the Phillips screw holding the blade in position. The Vital Zip works well for cutting webbing and rope and to remove clothing from injured persons in rescue situations. And its feather light aspect means it can be carried along on a belt or in a kit pack without adding undue weight to your gear.

Learn More

The Petzl ID is a self-braking descender with an anti-panic function built in. Learn More

Misty Mountain Challenge Harness – has quick adjust waist and leg buckles. Designed specifically for climbing gyms, ropes courses and challenge towers, the Challenge Harness is simple to use, safe and durable. It features a single reinforced tie-in point and pre threaded, quick adjust waist and leg loop buckles. The single tie in point, along with the quick adjust waist and leg buckles, provide for a quick set up and the durable components ensure much hard wear. Quick and convenient, the Challenge Harness is a great all around program harness.

Youth: Green tie-in point
Standard: Blue tie-in point
X-Large: Black tie-in point

Learn More

The CMI Velocity Micro Zipline trolley is a fast zip line trolley that is small and light weight. Stainless steel side plates assure long life and minimal wear. Learn More

This is a great low profile SRD with a parallel attachment to easily align cable and belay loading. Super strong with a triple axle design and a thick folded plate design. Learn More

Crosby Fist Grip Cable Clamps Learn More

Shoulder Eye Screw Lag, Use for connecting hand lines, spiders webs to trees, etc. on challenge courses. Do not use in life support applications. Also used when wrapping cable around a tree. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Stainless Steel Cable clamps are ideal for use in salty and acidic environments like zip lining close to oceans or salt lake. These are durable and outlast Drop Forged clamps in harsh environments. Learn More

The smallest and strongest knot passing pulley on the market today! With an incredible MBS of 15,000 lbs and high strength stainless steel, our knot passing pulley puts the others to shame. Learn More

Kong Furtura Chest Acscender Learn More

Designed by top cavers for tight places in the most remote areas on earth (or under it). Surprisingly simple the new designs are comfortable to use thanks to the ergonomic grips. Learn More

Petzl Caterpillar Edge Protector, The Caterpillar Edge Protector can be positioned independently to adapt to whatever the terrain throws at you Learn More

Yates Figure Eight Chest Harness, Great for use on zip line operations. Attachment points at waist and between shoulders. Safety attachment at rear of waist. Padded waist belt. Super easy to get on and adjust. Learn More

The Figure 8 by Omega Pacific remains a popular device for their simplicity, durability and dependability. Learn More

The HaulerBiner Compact Rescue Kit is a lightweight, compact and simple to use/deploy device. The HaulerBiner is fully rated for lifting people. The HaulerBiner has three pulley wheels incorporated into each carabiner, creating a compact and lightweight 6:1 or 7:1 (theoretical) mechanical advantage system. The HaulerBiner also has a purpose-designed progress capture cam with, an ‘on/off’ position.  The HaulerBiner utilises purpose-developed 6mm (1/4") rope, for strength and easy handling/best grip.  The kit is supplied in a two-pouch bag, for easy deployment. The HaulerBiner is load rated to 140kg (310lbs) but it has an MBS of at least 16kN/3500lbs tested as a complete system. The length of the system, when fully contracted is only 32cm (12"). EN 12278, EN 567 certifications

Learn More

CMI Double Expedition Ascender, The cam is the same design as those in our now famous Ultrascenders and carries the same lifetime wear-out guarantee. Extra large handgrip opening easily accomodates gloved or mittened hands Learn More

Nylon Shock Cord consists of a stranded rubber core covered with braided fiber resulting in an elastic cord with consistent stretch and strength. The durable "bungee type" cord is covered with nylon. Learn More

They fit securely on a wide range of flange widths and beam sizes, with a built-in suspension bar that provides for close mounting. The clamp jaw design reduces flange stress by distributing the load away from the flange edge. Learn More

The AIRLINE throw-line offers an excellent compromise between flexibility and rigidity, for an accurate throw without the formation of knots as it comes out of the bag. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More