Search results for: 'harness rope climbing'

The Petzl Vrillee hanger is for direct aid. It holds the carabiner parallel to the rock face allowing the rope to run easily through the carabiner. With 8mm bolt Learn More

CMI EXPEDITION ASCENDER, The Expedition Ascender is a perfect choice for big wall or mountaineering endeavors. Engineered for comfort, the handle opening is extra wide to accommodate gloved hands. Works with 7mm-12mm ropes. Sold individually. Learn More

The RING OPEN gated ring is designed for the semi-permanent connection of equipment. Its round shape ensures optimal functioning in all directions. It has a wide opening that allows installation of ropes with sewn terminations. Learn More

GREAT ECONOMICAL BELAY DEVICE. If you are looking for a good ATC style belay device, this is it: Cypher ARC Rappel and Belay Device. Crafted from high-density aircraft-grade aluminum, the ARC is engineered to keep your rope running smoothly through the device for quick payouts and long rappels. Learn More

Forged Nut Eye bolts are the backbone of ropes challenge course and zip line construction. Zip line and other cables are terminated to the eye bolt around a thimble to prevent cable deformation at the turn back. Learn More

Stainless Steel Thimbles, When the zip line wire rope is terminated with a loop, there is a risk that the wire rope can bend too tightly, especially when the loop is connected to a device that spreads the load over a relatively small area. Learn More

Nut Eye bolts are the main bolts used in ropes challenge course and zip line construction. Zipline and other cables are terminated to the eye bolt around a thimble to prevent cable deformation at the turn back. Learn More

This industrial size carabiner combines a wide gate opening and high strength, useful for attaching to rungs on aerial ladders, buckets and industrial rescue or rope access anchors points that are too big for the large rescue carabiners. Learn More

Nut Eye bolts are the main bolts used in ropes challenge course and zip line construction. Zipline and other cables are terminated to the eye bolt around a thimble to prevent cable deformation at the turn back. Learn More

We offer three different style of pilot auger bits for 1/2" lags for ropes course decks, zip line decks and general deck construction for 1/2" & 5/8" lag bolts Learn More

Lag Screw Lag Bolt - Galvanized, Typically used for LEAP anchors, deck constuction for zip lines and ropes courses. Hot Dipped Galvanized; Hex Head Lag Screw. 5/8" x 6" lags or 5/8" x 8" lags are recommended for Leap/Lead/Bolt hanger anchors where through bolts are not required Learn More

These splicing fids are used to make splicing rope easier. Fid is made from stainless steel and hardwood.  Comes in two sizes

Small: for rope sizes up to 58"

Large: for rope sizes 5/8" and larger

Learn More

Petzl Paw Rigging Plate, Coming in three sizes for different set ups the PAW provides strong and lightweight organization for your rope set up. Learn More

Deep Cut telephone Pole Auger Bits: 24", Super long 24" Pole Auger Bits for telephone poles, utility poles, treated poles, ropes course and zip line poles. Designed for making deep cuts in utility poles, pressure treated lumber, railroad ties, and wet or frozen lumber. Learn More

The perfect size for light and tower rescues. Fits ropes from 8mm to 1/2". Features built in safety cam for use in "jigger" or "short haul" systems. Use with CMI micro single or double pulley 3:1 or 4:1 mechanical advantage systems. Features a centered bronze bushing. Strength: 7000 lbs. The CMI Single Micro Hauler is 154 mm. tall, 53 mm wide, and 40 mm. thick and 19 g. Learn More

A smooth feeding, controlled braking device that looks great. Notch on one side of the device provides additional braking friction for thinner ropes giving you controlled descents and belays. Use on 8mm to 12mm ropes.

• Weight: 54 grams
• Rope Diameter Range: 8mm - 12mm
• CE EN15151-2

Learn More

The best brake for your zip line,Head Rush zipSTOP Zip Line Brake uses Head Rush's self-regulating eddy current magnetic braking system to brake zip line riders smoothly, comfortably, and consistently, even at high speeds. Learn More

Steel cable with aluminum rungs. Can be used in ropes courses, caving, rope access work, or emergency preparedness kits.

• Length 32 feet
• Weight: 3 lbs 4 oz.
• Width: 6"
• Breaking Strength: 1324 lbs.

Learn More

Stainless steel sideplates, 3" red anodized aluminum sheave, bushing, and stainless steel axle. 

*Exceeds tests for national fire protection association standard on fire service life safety rope and system components NFPA 1983-2006 edition. 

 

MBS	Rope Capacity	Size	Weight	Efficiency
16000lbs	1/2"	6.75x5.25in	1.65lb	91.7%

 

 

 

Learn More

Red/Black anodized aluminum sideplates, two 3" aluminum sheaves, bushing, and stainless steel axle. 

 *Exceeds tests for national fire protection association standard on fire service life safety rope and system components NFPA 1983-2006 edition.  *Not Certified*

 

MBS	Rope Capacity	Size	Weight	Efficiency
12000lbs	1/2"	10x4in	2.6lb	184%

Learn More

Multiline 3-Strand Spliced Rope Zip Line Lanyards (tethers). Plastic teardrop shaped thimble on each end.

Learn More

Nail Chipper Tri-Cut Auger Bits, Typically when drilling a hole for a through bolt as used in ropes course or zip line construction, you will need to drill a hole 1/16" bigger than the bolt you are using. 5/8" bolt requires a 11/16" hole. These are all 18" long bits. 7-1/2" are available by request. Learn More

The Rescue Figure 8 is a special figure 8 for rescue situations and fast rappeling.  It has a special shap for multiple rope locking, allows rappeling with heavy loads, has a high strength, and fits a wide range of rope diameters. Available in light alloy or stainlees steel.

• Weight: 154g, 5.43oz (alloy) 451g, 15.9 oz (stainless steel)
• Material: Light alloy or stainless steel
• Strength: 40kN

Learn More

Stainless steel sideplates, 3"aluminum sheave, bushing, and stainless steel axle. 

 

MBS	Rope Capacity	Size	Weight	Efficiency
16000lbs	5/8"	6.5x4.25in	1.35lb	92.1%

Learn More

Stainless steel sideplates, 2" aluminum sheave, needle bearing, and stainless steel axle.

 

MBS	Rope Capacity	Size	Weight	Efficiency
8000lbs	1/2"	5x2.5in	0.5lb	90.6%

Learn More

Black anodized aluminum sideplates, 2 3/8" zinc coated steel sheave, bushing, and stainless steel axle. 

MBS	Cable/Rope Capacity	Size	Weight	Efficiency
6000lbs	5/8"	4.375x3.5in	0.75lb	91.4%

 

Learn More

 

Learn More

The SWIVEL OPEN gated swivel features a wide opening and thus can be attached to a range of products (pulleys, lanyards). It reduces the bulk and weight of component systems and solves the twisting and tangling problems of ropes and lanyards. Sealed ball bearings offer excellent performance and reliability.

Learn More

RSRP431 R-ALF Rescue Hauler Pulley- 2 Way Auto Locking Approved standards CE 0120 ANSI Z359 :4: 2007

 The R-ALF Pulley is the latest innovation in Accessability, Rescue, Confined Space working and Work Suspension Systems. The R-ALF Pulley has an over-speed brake built in so that the Pulley will lock on and hold when a fall occurs. The load rated Becket Eye on the R-ALF means that it can be used in combination with Prussic Pulleys to create a 3: 1 or 5: 1 Mechanical Advantage System. The unique design of the R-ALF (design patent applied for), means that an internal brake is not required and therefore it is capable of several thousand cycles and many arrests (minimum 12 monthly service intervals apply). Weight (grams) 1200 Weight (ounces) 43 Rope diameter range (mm) Approved 11mm EN1891-A Ropes Only Number of persons 2

Learn More

 Rescue Swivel helps to eliminate twisting in critical lines due to load rotation. Its 9000lb (40kN) MBS gives you piece of mind when moving the heaviest of loads, and its sealed ball bearing will keep it operating smoothly for years.

*Exceeds tests for national fire protection association standard on fire service life safety rope and system components NFPA 1983-2006 edition.  *Not Certified*

Size: 4 1/4" x 1 3/4"
Weight: 5.6 oz
Breaking Strength: 9,000 pounds

Learn More

The D4 Work/Rescue Descender features a unique and innovative cam action, which offers precise control at slow or fast speeds. The progressive cam works by way of one cam operating inside another cam. The D4 is the only ANSI certified descender on the market today.

• Weight: 655 grams (23 ounces)
• Strength: MBS 16kN (3597lbf)
• For use with single ropes from 10.5 - 11.5mm (7/16")
• Working Load Rating (WLL): 240kg (551lbs.)
• Certifications: CE EN12841, NFPA 1983, ANSI Z359

Learn More

A Super-efficient slicing tool that makes the most of its simple design and sturdy construction, the Vital Zip Knife holds a utility blade which is easily replaced once dull with a quick release of the Phillips screw holding the blade in position. The Vital Zip works well for cutting webbing and rope and to remove clothing from injured persons in rescue situations. And its feather light aspect means it can be carried along on a belt or in a kit pack without adding undue weight to your gear.

Learn More

The Petzl ID is a self-braking descender with an anti-panic function built in. Learn More

Pulley carabiner, available in versions with or without TRIACT-LOCK locking system. Learn More

Petzl ZigZag Prusik The linked rings provide precision and fluidity when moving around. The pulley is mounted on ball bearings to allow the slack to be taken up easily. Learn More

The Redirection Pulley is the first pulley of its kind for the zip line industry; lightweight, corrosion-resistant and specially engineered to be virtually resistant to snagging. Learn More