Search results for: 'wire rope clamp p03a numer'

Cable Clamp: Crosby Wire Rope Clip Learn More

GIANT SWING / SUSPENSION CLAMP FOR 3/8" CABLE

Galvanized Ductile Iron

Learn More

Great for ropes courses, zip line, high elements, and low ropes challenge courses. Cable Clamps, sometimes called cable stops or cable clips, are tools that are used to clamp down on wire rope commonly used in industrial applications as well as in zip lining and ropes course construction. Learn More

When the zip line wire rope is terminated with a loop, there is a risk that the wire rope can bend too tightly, especially when the loop is connected to a device that spreads the load over a relatively small area. Learn More

The RC-800 Wire Rope Cutters are used for cutting 1/16 to 5/8 inch cable. Learn More

Zip Line Super Swaged Compacted Cable / Wire Rope - Zip Line Super cable aka Swaged galvanized cable or compacted wire rope is now available! This incredible cable has at least five times the life of ordinary cable, 25% more strength, 10% faster, and runs 50-70% quieter than traditional cable! This is the wire rope to use for a smoth zipline ride.

Learn More

Stainless Steel Cable clamps are ideal for use in salty and acidic environments like zip lining close to oceans or salt lake. These are durable and outlast Drop Forged clamps in harsh environments. Learn More

The Felco C16 Wire Cutter has a capacity of 5/8 in. diameter and smaller. This is the GO-TO zipline cable cutter in the industry. Felco cutters keep cutting for years longer than other cable cutters. Learn More

Our Galvanized Aircraft Zip Lining Cable is made in accordance with Federal Specification RR-W-410D, meeting the dimensional and strength requirements of MIL-W-83420D. Learn More

They fit securely on a wide range of flange widths and beam sizes, with a built-in suspension bar that provides for close mounting. The clamp jaw design reduces flange stress by distributing the load away from the flange edge. Learn More

Our Galvanized Aircraft Zip Lining Cable is made in accordance with Federal Specification RR-W-410D, meeting the dimensional and strength requirements of MIL-W-83420D. Learn More

Our Galvanized Aircraft Zip Lining Cable is made in accordance with Federal Specification RR-W-410D, meeting the dimensional and strength requirements of MIL-W-83420D. Learn More

Crosby Fist Grip Cable Clamps Learn More

Cable Drop Plate, The lower 1" tie-in hole allows easy attachment of a carabiner or quicklinks. Hot dip galvanized for lasting durability. Cable drop plates are great for giant ladders, giant swings, rope climbs, tire crossings or just about any ropes course element Learn More

Fist Grip Cable Clamp - Import Learn More

Our Galvanized Aircraft Zip Lining Cable is made in accordance with Federal Specification RR-W-410D, meeting the dimensional and strength requirements of MIL-W-83420D. Learn More

The Felco C112 Cutter features maximum force transmission which applies the maximum leverage at just the right moment. This coupled with Swiss precision blades make this cutter very easy to use. Learn More

The VERTIGO WIRE-LOCK carabiner is designed for use on via ferrata lanyards along with zipline systems and ropes courses. Learn More

atented cable grabs are designed to provide fall protection for workers ascending or descending from a variety of ladders or vertical structures. The stainless steel cable grab is easily removed or repositioned along a cable. If a fall occurs, the cable grab is designed to immediately lock onto the cable and prevent a free fall. Sold with an integrated shock absorber. Users should be familiar with all warnings and instructions and receive training in the proper use of this device. Product Specs: Universal design Auto traveling operation Durable, lightweight stainless steel design Meets applicable OSHA Standards and ANSI requirements. Recommended lifelines 3/8″ diameter stainless steel or galvanized 7×19 aircraft cable (non-lubed) with minimum tensile strength of 8,000 lbs.

MUST be attached to worker’s harness using ANSI rated autolocking carabiner (NOT included)

Learn More

Zipline Cable Ferrule - Zinc Plated, Two ferrules are required for life support and ziplining applications (ACCT Standards). The extra ferrule serves as a backup in case of primary ferrule failure due to defects or improper swaging. A 12 ton crimper/compression tool is required for 1/4" - 1/2" ferrules Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

Gripple Ropes Course Cable Connector, Learn More

Width:	1.56 in
Strand Size:	1/4 to 7/16 in
Specifications:	100 ft-lb Minimum Bolt Torque
Finish:	Hot Dipped Galvanized
Length:	4 in
Material:	Steel
Clamping Bolt Size:	1/2 in
Suitable For Use With:	Loop Type Guy Dead End
Order Interval:	1
Vendor SKU:	6449
Standard & Approvals:	ARRA Compliant|Buy American Act Compliant|ASTM A153
Manufacturer:	Hubbell
Includes:	(3) Bolts
Brand:	CHANCE®
Features & Benefits:	Parallel grooves trap strand tightly without marring Each bolt has a shoulder to prevent turning while tightening

Learn More

Handled rope clamp designed for doubled rope ascents, the ASCENTREE has ergonomic handles allowing a comfortable and powerful grip when pulling. Learn More

8' long (96") Yellow High density polyethylene guy guard marker. 1.51" OD collapses to 1.375" once installed Learn More

100% polyester static kernmantle construction that is lightweight and offers super low-elongation. Learn More

Petzl Rope Bucket, The Petzl Rope Bucket has a unique tapered design and thin layer of closed cell foam enable the bag to stand up by itself and stay open. Learn More

A 1" Climbing Rope and/or a Swing Rope. We make our 1" Climbing/Swing Ropes with Multiline II Rope. Multiline II Rope is strong, durable and resistant to UV rays. Our 1-1/2" Ropes are made with Combo Rope, aka poly-dac rope, which is similar to Multiline. The 1" Nitro Swing Rope also have a Pear Shaped Sling Link on the thimble to make it possible to hang them with a Rapid Link. All of these ropes have a metal thimble at one end and a back-splice at the other end.We offer multiple lengths. If you require a length other than what we have listed; please give us a call at (877) 206-8967

Learn More

The Ascension Ascender by Petzl is the benchmark for handled ascenders and has been refined to provide greater comfort; efficiency, ease of use. Learn More

A 5/8" Climbing Rope and/or a Swing Rope. We make our 5/8"Climbing/Swing Ropes with Multiline II Rope. Multiline II Rope is strong, durable and resistant to UV rays. Our 1-1/2" Ropes are made with Combo Rope, aka poly-dac rope, which is similar to Multiline. All of these ropes have a metal thimble at one end and a back-splice at the other end.We offer multiple lengths. If you require a length other than what we have listed; please give us a call at (877) 206-8967

Learn More

Rope thimbles protect the rope from wear whenever you have a fixed loop in the end of the rope, whether the rope is tied, spliced, or swaged. Learn More

The Head Rush Gorilla Rope is specially designed to work as a reduction line for zipSTOP zipline braking system. Brings high strength, a long life span, and minimal stretch to your zipline runs. Learn More

This professional heavy-duty cutter cuts and fuses ends of polyester and nylon ropes and web quickly. Learn More

The 5.4 mm V-TX Cord is the ultra-lightweight, super low-stretch addition to our High Tenacity Cord series. Learn More