Search results for: '200 tools cabl f1 formula 1 rope sapphire'

The 1/4, 5/16, and 3/8 Swaging Tools are designed for crimping copper and aluminum oval sleeves and stop sleeves on zip lines, life lines,ropes course elements. Learn More

Cable Clamp: Crosby Wire Rope Clip Learn More

Zipline Cable Ferrule - Zinc Plated, Two ferrules are required for life support and ziplining applications (ACCT Standards). The extra ferrule serves as a backup in case of primary ferrule failure due to defects or improper swaging. A 12 ton crimper/compression tool is required for 1/4" - 1/2" ferrules Learn More

Our Galvanized Aircraft Zip Lining Cable is made in accordance with Federal Specification RR-W-410D, meeting the dimensional and strength requirements of MIL-W-83420D. Learn More

CIFA: 10286 Klein Tools 809-36 hammer is designed and created to strike through jobsite challenges. Engineered with the professional in mind, each tool is job-matched to fit the task at hand. Features: Designed for pole-line work   Rugged and well-balanced, with the weight to drive lag bolts   Forged, tempered-steel head for use in tight areas   Identical faces with round-crown driving surface and beveled edges

Learn More

Our Galvanized Aircraft Zip Lining Cable is made in accordance with Federal Specification RR-W-410D, meeting the dimensional and strength requirements of MIL-W-83420D. Learn More

Gripple Ropes Course Cable Connector, Learn More

Great for ropes courses, zip line, high elements, and low ropes challenge courses. Cable Clamps, sometimes called cable stops or cable clips, are tools that are used to clamp down on wire rope commonly used in industrial applications as well as in zip lining and ropes course construction. Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

Our Galvanized Aircraft Zip Lining Cable is made in accordance with Federal Specification RR-W-410D, meeting the dimensional and strength requirements of MIL-W-83420D. Learn More

Our Galvanized Aircraft Zip Lining Cable is made in accordance with Federal Specification RR-W-410D, meeting the dimensional and strength requirements of MIL-W-83420D. Learn More

A 1" Climbing Rope and/or a Swing Rope. We make our 1" Climbing/Swing Ropes with Multiline II Rope. Multiline II Rope is strong, durable and resistant to UV rays. Our 1-1/2" Ropes are made with Combo Rope, aka poly-dac rope, which is similar to Multiline. The 1" Nitro Swing Rope also have a Pear Shaped Sling Link on the thimble to make it possible to hang them with a Rapid Link. All of these ropes have a metal thimble at one end and a back-splice at the other end.We offer multiple lengths. If you require a length other than what we have listed; please give us a call at (877) 206-8967

Learn More

CONNEXION FIXE Anchor strap, Forged steel D-rings on the ends. The Connexion Fixe anchor strap is the climbers choice for top rope anchor systems. This anchor strap is the best for rock climbing rope systems. Learn More

Waterbased formula is more environmentally friendly and easy to clean up. Whip-End Dip was designed to seal the end of a rope to prevent fraying or unraveling. Learn More

100% polyester static kernmantle construction that is lightweight and offers super low-elongation. Learn More

Trapeze bar designed for use on ropes challenge courses: leap of faith. Our Trapeze Bar is made from 1-1/2" solid high density PVC. Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

1 1/2: Manila rope Learn More

Designed for use on Challenge ropes course/Zip Lining traverses, on cable or rope. Super strong with a 10,000 rating and a sheathed back up bolt. Stainless steel sides make this cable pulley bomb proof. Learn More

Crosby Fist Grip Cable Clamps Learn More

Fist Grip Cable Clamp - Import Learn More

Zip Line Super Swaged Compacted Cable / Wire Rope - Zip Line Super cable aka Swaged galvanized cable or compacted wire rope is now available! This incredible cable has at least five times the life of ordinary cable, 25% more strength, 10% faster, and runs 50-70% quieter than traditional cable! This is the wire rope to use for a smoth zipline ride.

Learn More

The Klein Haven Cable Grip is designed for use when a light, compact grip is desired and where zipline or other cable damage is not a factor. Gripping pressure of the knurled jaw s applied to ¼” of zipline cable area. Learn More

Rope thimbles protect the rope from wear whenever you have a fixed loop in the end of the rope, whether the rope is tied, spliced, or swaged. Learn More

This self-trailing MIO rope grab grips automatically in the event of a fall and dissipates the energy of the fall by slipping along the rope. When used within OSHA guidelines on approved ropes, the amount of slip is well within the OSHA requirements. This rope grab comes with a lanyard and an ANSI Snap Hook. for use on 1/2" ropes.

 

Learn More

3 Strand Import Polydacron Rope combines filament and staple/spun polyester wrapped around a polyolefin core to produce a rope with considerably lower stretch, better wear life and superior handling characteristics.

• Color: White/Red
• Material: Polyester Blend
• Construction: 3 Strand
• Easy to splice
• Ideal for Element Construction

Learn More

When the zip line wire rope is terminated with a loop, there is a risk that the wire rope can bend too tightly, especially when the loop is connected to a device that spreads the load over a relatively small area. Learn More

Teufelbergers - New England Ropes 3 Strand Multiline II is a unique construction that combines filament and staple/spun polyester wrapped around a polyolefin core to produce a rope with considerably lower stretch, better wear life and superior handling characteristics.

• Color: White/Orange
• Material: Polyester Blend
• Construction: 3 Strand
• Easy to splice
• Ideal for rigging

Learn More

atented cable grabs are designed to provide fall protection for workers ascending or descending from a variety of ladders or vertical structures. The stainless steel cable grab is easily removed or repositioned along a cable. If a fall occurs, the cable grab is designed to immediately lock onto the cable and prevent a free fall. Sold with an integrated shock absorber. Users should be familiar with all warnings and instructions and receive training in the proper use of this device. Product Specs: Universal design Auto traveling operation Durable, lightweight stainless steel design Meets applicable OSHA Standards and ANSI requirements. Recommended lifelines 3/8″ diameter stainless steel or galvanized 7×19 aircraft cable (non-lubed) with minimum tensile strength of 8,000 lbs.

MUST be attached to worker’s harness using ANSI rated autolocking carabiner (NOT included)

Learn More

Cable Drop Plate, The lower 1" tie-in hole allows easy attachment of a carabiner or quicklinks. Hot dip galvanized for lasting durability. Cable drop plates are great for giant ladders, giant swings, rope climbs, tire crossings or just about any ropes course element Learn More

The RC-800 Wire Rope Cutters are used for cutting 1/16 to 5/8 inch cable. Learn More

Stainless Steel Cable clamps are ideal for use in salty and acidic environments like zip lining close to oceans or salt lake. These are durable and outlast Drop Forged clamps in harsh environments. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More