Search results for: 'pole reduc'

Deep Cut telephone Pole Auger Bits: 24", Super long 24" Pole Auger Bits for telephone poles, utility poles, treated poles, ropes course and zip line poles. Designed for making deep cuts in utility poles, pressure treated lumber, railroad ties, and wet or frozen lumber. Learn More

Deep Cut Pole Auger Bits Learn More

Detachable Pole and Tree Step, These are the preferred security steps for ropes challenge courses either rin trees or poles. Lag bolt and plate are installed into a ropes course pole or tree. Learn More

Just Perfect Pole Steps : JP Step II

 

The JP Step I and JP Step II  are Pole/Tree steps and fall protection anchor in one (think integrated LEAD anchor). Installs with 5/8" x 6" lag in poles and 5/8" x 8" lag in trees for the JP I and II. The JP R uses a Specialty 4" Lag Bolt and plate that comes with it. Supports over 5,000 lbs when properly installed. A great alternative to traditional pole steps and staples.  These pole/tree steps are easily installed (about one minute). They also provide great positive climbing aids for hands, feet, and safety anchors. JP Steps for trees and poles are the best looking and safest integrated step - fall protection anchor for ropes courses, challenge courses, and zip line access.

Learn More

Just Perfect Pole Steps : JP Steps Removable utility pole and tree steps

Learn More

Just Perfect Pole Steps : JP Steps Removable utility pole and tree steps. This is the step only. These steps can replace common utility pole steps that have an upturned hook end.

Learn More

Lock washers are a critical component to through bolts on wood poles. Pole shrinkage mandates the use of double coil lock washers to keep pressure on the nut and bolt to prevent loosening. Learn More

3/4" Timber Bolts, Super strong and easy to install, Timber bolts are used for pole to pole attachments, deck beam mounts, climbing towers, climbing walls, adventure towers, high ropes course elements and low ropes course elements Learn More

Figure 8 descender, compact and lightweight. Square shape helps reduce rope twist. Learn More

Shock absorbing sling designed to reduce peak loads in any climbing system!! Learn More

Effectively reduces peak loads on an anchor in rescue and rigging system. Learn More

The TOP chest harness transforms the AVAO SIT, FALCON and SEQUOIA SRT seat harnesses into fall arrest harnesses. The foam shoulder straps are widely spaced to reduce neck chafing. Learn More

Yates Speed Wall Ladders are designed with the same configuration as the Big Wall Ladders but have 1" wide steps to reduce bulk and weight. Learn More

Yates Adjustable Daisy Strap W/ Screamer, Designed to reduce shock loading during aid climbing situations where protection fails result in a direct fall onto the lower daisy. Learn More

Yates Adjustable Daisy Strap, The buckle axle is riveted for added security and strength. Contoured webbing eye at carabiner clip attachment end. This configuration allows the strap more rotation, thus reducing jamming in corners. Learn More

The handy alternative for shorter drops or lighter loads. To reduce weight, the rack is drawn from 5/16" stainless steel, and the solid bars are formed from anodized aluminum. Learn More

The handy alternative for shorter drops or lighter loads. To reduce weight, the rack is drawn from 5/16" stainless steel, and the solid bars are formed from anodized aluminum. Learn More

We chose stainless steel over aluminum because of its "wearever" qualities. In order to compensate for the reduced friction inherent in stainless bars, we increased the radius of the friction surface to a full 1/2". Learn More

Compact self-braking descender, Lock off and work with minimum gear to tangle. The Petzl Rig is a proven performer for the zip line and ropes course construction industry. Learn More

They fit securely on a wide range of flange widths and beam sizes, with a built-in suspension bar that provides for close mounting. The clamp jaw design reduces flange stress by distributing the load away from the flange edge. Learn More

Ropes Course Zip Line Staples, Staples are the preferred way access ropes challenge course elements and zip line platforms: easy to install, easy to inspect, and easy to climb. If properly installed, the 8" staples can perform as fall protection anchors Learn More

GUY ANCHORS- Helix Ground Anchors, Multiple sizes and capacities allow precise designs for the adventure and zip line industry. There may be one or multiple guywires that can be resisted by one or multiple guy wire anchors, dictated by design and load requirements. Learn More

Lag Screw Lag Bolt - Galvanized, Typically used for LEAP anchors, deck constuction for zip lines and ropes courses. Hot Dipped Galvanized; Hex Head Lag Screw. 5/8" x 6" lags or 5/8" x 8" lags are recommended for Leap/Lead/Bolt hanger anchors where through bolts are not required Learn More

Shoulder Eye Screw Lag, Use for connecting hand lines, spiders webs to trees, etc. on challenge courses. Do not use in life support applications. Also used when wrapping cable around a tree. Learn More

The Universal Mount is a mounting device designed specifically for use as a climbing anchor. Learn More

GUY ANCHORS- Helix Ground Anchors : 6" x 3/4" x 66" Learn More

GUY ANCHORS- Helix Ground Anchors : 10" x 1-1/4" x 96" Learn More

GUY ANCHORS- Helix Ground Anchors : 8" x 1" x 66" Learn More

GUY ANCHORS- Helix Ground Anchors : 4" x 3/4" x 54" Learn More

Yates Gym Harness, "New" Light weight "Cam Lock" quick adjust leg and waist buckle option allows the Gym Harness to be easily adjusted with added security. Learn More

The Redirection Pulley is the first pulley of its kind for the zip line industry; lightweight, corrosion-resistant and specially engineered to be virtually resistant to snagging. Learn More

Square Curved Washers for nut eye bolts and machine bolts. Galvanized Square washers designed for outdoor use in challenge courses, zip lines and other outdoor applications. Learn More

Yellow 8' Guy Marker - Guy Guard Learn More

Klein Tools' Lineman's Wrenches are forged from special bar steel and heat-treated for durability and long life. These wrenches are designed for use on heavy three-bolt guy clamps where clearance is limited. Each end has two different size openings, plus a hole at the larger end for turning-in standard pole steps.

• Forged from special bar steel and heat-treated for long life
• Each end has two different size openings
• Small end has 5/8-Inch and 13/16-Inch openings; large end features 29/32-Inch and 1-3/32-Inch openings
• Hole is provided at larger end for turning-in standard pole steps
• Made in USA
• Wrench is suited for use on the heavy three-bolt guy clamps on which clearance is limited
• Dark blue painted finish

Learn More

AVAO BOD Harnesses, The harness also facilitates carrying and organization of tools with multiple equipment loops and retainers for attaching CARITOOL tool holders and TOOLBAG tool-holder pouches. Learn More

The Universal Mount is a simple and durable mounting point for auto belays and top rope anchors.

Learn More