Search results for: 'stainless stapl cabl clamp'

Stainless Steel Cable clamps are ideal for use in salty and acidic environments like zip lining close to oceans or salt lake. These are durable and outlast Drop Forged clamps in harsh environments. Learn More

Great for ropes courses, zip line, high elements, and low ropes challenge courses. Cable Clamps, sometimes called cable stops or cable clips, are tools that are used to clamp down on wire rope commonly used in industrial applications as well as in zip lining and ropes course construction. Learn More

Ropes Course Zip Line Staples, Staples are the preferred way access ropes challenge course elements and zip line platforms: easy to install, easy to inspect, and easy to climb. If properly installed, the 8" staples can perform as fall protection anchors Learn More

Cable Clamp: Crosby Wire Rope Clip Learn More

Cable Drop Plate, The lower 1" tie-in hole allows easy attachment of a carabiner or quicklinks. Hot dip galvanized for lasting durability. Cable drop plates are great for giant ladders, giant swings, rope climbs, tire crossings or just about any ropes course element Learn More

Crosby Fist Grip Cable Clamps Learn More

Fist Grip Cable Clamp - Import Learn More

They fit securely on a wide range of flange widths and beam sizes, with a built-in suspension bar that provides for close mounting. The clamp jaw design reduces flange stress by distributing the load away from the flange edge. Learn More

Stainless Steel Thimbles, When the zip line wire rope is terminated with a loop, there is a risk that the wire rope can bend too tightly, especially when the loop is connected to a device that spreads the load over a relatively small area. Learn More

GIANT SWING / SUSPENSION CLAMP FOR 3/8" CABLE

Galvanized Ductile Iron

Learn More

Learn More

Learn More

Our enhancements include adjustable spring tension, a reversible cable and pin, and "mud vents" to help prevent dirt caked on rope from degrading ascender performance. Learn More

Learn More

Stainless steel sideplates, 2" aluminum sheave, needle bearing, and stainless steel axle.

 

MBS	Rope Capacity	Size	Weight	Efficiency
8000lbs	1/2"	5x2.5in	0.5lb	90.6%

Learn More

This manual rescue belay can be used as a self belay or with a belayer. The side plates and drum are made from heat treated 6061 T6 Aluminum while the two stainless steel pins keep the rope seperated as it is reaved around the drum. Drum is Aircraft Hard Anodized for extended wear which cost more but makes for a superior product. Learn More

Width:	1.56 in
Strand Size:	1/4 to 7/16 in
Specifications:	100 ft-lb Minimum Bolt Torque
Finish:	Hot Dipped Galvanized
Length:	4 in
Material:	Steel
Clamping Bolt Size:	1/2 in
Suitable For Use With:	Loop Type Guy Dead End
Order Interval:	1
Vendor SKU:	6449
Standard & Approvals:	ARRA Compliant|Buy American Act Compliant|ASTM A153
Manufacturer:	Hubbell
Includes:	(3) Bolts
Brand:	CHANCE®
Features & Benefits:	Parallel grooves trap strand tightly without marring Each bolt has a shoulder to prevent turning while tightening

Learn More

Designed for use on Challenge ropes course/Zip Lining traverses, on cable or rope. Super strong with a 10,000 rating and a sheathed back up bolt. Stainless steel sides make this cable pulley bomb proof. Learn More

Gripple Ropes Course Cable Connector, Learn More

8' long (96") Yellow High density polyethylene guy guard marker. 1.51" OD collapses to 1.375" once installed Learn More

Zip Line Super Swaged Compacted Cable / Wire Rope - Zip Line Super cable aka Swaged galvanized cable or compacted wire rope is now available! This incredible cable has at least five times the life of ordinary cable, 25% more strength, 10% faster, and runs 50-70% quieter than traditional cable! This is the wire rope to use for a smoth zipline ride.

Learn More

Zipline Cable Ferrule - Zinc Plated, Two ferrules are required for life support and ziplining applications (ACCT Standards). The extra ferrule serves as a backup in case of primary ferrule failure due to defects or improper swaging. A 12 ton crimper/compression tool is required for 1/4" - 1/2" ferrules Learn More

The Fat Cat is from a line of proven performers for zip line operations: Robertson Mountaineering. This specialized design works great for the thicker and larger 1/2" - 3/4" cables used more and more by zip line tours and canopy tours. Learn More

atented cable grabs are designed to provide fall protection for workers ascending or descending from a variety of ladders or vertical structures. The stainless steel cable grab is easily removed or repositioned along a cable. If a fall occurs, the cable grab is designed to immediately lock onto the cable and prevent a free fall. Sold with an integrated shock absorber. Users should be familiar with all warnings and instructions and receive training in the proper use of this device. Product Specs: Universal design Auto traveling operation Durable, lightweight stainless steel design Meets applicable OSHA Standards and ANSI requirements. Recommended lifelines 3/8″ diameter stainless steel or galvanized 7×19 aircraft cable (non-lubed) with minimum tensile strength of 8,000 lbs.

MUST be attached to worker’s harness using ANSI rated autolocking carabiner (NOT included)

Learn More

Our Galvanized Aircraft Zip Lining Cable is made in accordance with Federal Specification RR-W-410D, meeting the dimensional and strength requirements of MIL-W-83420D. Learn More

Black anodized aluminum sideplates, 2 3/8" zinc coated steel sheave, bushing, and stainless steel axle. 

MBS	Cable/Rope Capacity	Size	Weight	Efficiency
6000lbs	5/8"	4.375x3.5in	0.75lb	91.4%

 

Learn More

Our Galvanized Aircraft Zip Lining Cable is made in accordance with Federal Specification RR-W-410D, meeting the dimensional and strength requirements of MIL-W-83420D. Learn More

Our Galvanized Aircraft Zip Lining Cable is made in accordance with Federal Specification RR-W-410D, meeting the dimensional and strength requirements of MIL-W-83420D. Learn More

Our Galvanized Aircraft Zip Lining Cable is made in accordance with Federal Specification RR-W-410D, meeting the dimensional and strength requirements of MIL-W-83420D. Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

Zip Line LEAP Anchor, A high-strength, multi-purpose anchor that can be used equally well as self-belay anchors on staple climbs or as the ideal termination fitting on belay cables anywhere where the cable load is at 90° to the angle of the bolt Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

This Cable Spooler is Made of sturdy heavy-duty steel tubing and folds for easy storage and had a tough, durable finish.

• Maximum reel width: 18";
• Height from floor to rod: 13"
• Weight: 7.5lbs;
• Holds: 200lbs.

Learn More

The 1/4, 5/16, and 3/8 Swaging Tools are designed for crimping copper and aluminum oval sleeves and stop sleeves on zip lines, life lines,ropes course elements. Learn More