Search results for: 'tri acct stapl caribeener'

Ropes Course Zip Line Staples, Staples are the preferred way access ropes challenge course elements and zip line platforms: easy to install, easy to inspect, and easy to climb. If properly installed, the 8" staples can perform as fall protection anchors Learn More

Nail Chipper Tri-Cut Auger Bits, Typically when drilling a hole for a through bolt as used in ropes course or zip line construction, you will need to drill a hole 1/16" bigger than the bolt you are using. 5/8" bolt requires a 11/16" hole. These are all 18" long bits. 7-1/2" are available by request. Learn More

Adjustable Lobster Claws w/ Snap Hooks and Tri Fold and Girth Hitch Learn More

Registration per person for 2023 ACCT Test day in Madison WI.

Learn More

Zip Line LEAP Anchor, A high-strength, multi-purpose anchor that can be used equally well as self-belay anchors on staple climbs or as the ideal termination fitting on belay cables anywhere where the cable load is at 90° to the angle of the bolt Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

Zipline Cable Ferrule - Zinc Plated, Two ferrules are required for life support and ziplining applications (ACCT Standards). The extra ferrule serves as a backup in case of primary ferrule failure due to defects or improper swaging. A 12 ton crimper/compression tool is required for 1/4" - 1/2" ferrules Learn More

The Rope Ladder provides moderately challenging access to high elements or an alternative to staple climbs. Constructed of double lashed hardwood dowels with waxed nylon cord to increase durability. Professional installation required.

 

Cost is by: LINEAR FOOT 

Learn More

Just Perfect Pole Steps : JP Step II

 

The JP Step I and JP Step II  are Pole/Tree steps and fall protection anchor in one (think integrated LEAD anchor). Installs with 5/8" x 6" lag in poles and 5/8" x 8" lag in trees for the JP I and II. The JP R uses a Specialty 4" Lag Bolt and plate that comes with it. Supports over 5,000 lbs when properly installed. A great alternative to traditional pole steps and staples.  These pole/tree steps are easily installed (about one minute). They also provide great positive climbing aids for hands, feet, and safety anchors. JP Steps for trees and poles are the best looking and safest integrated step - fall protection anchor for ropes courses, challenge courses, and zip line access.

Learn More

We offer three different style of pilot auger bits for 1/2" lags for ropes course decks, zip line decks and general deck construction for 1/2" & 5/8" lag bolts Learn More

3 Strand Import Polydacron Rope combines filament and staple/spun polyester wrapped around a polyolefin core to produce a rope with considerably lower stretch, better wear life and superior handling characteristics.

• Color: White/Red
• Material: Polyester Blend
• Construction: 3 Strand
• Easy to splice
• Ideal for Element Construction

Learn More

Teufelbergers - New England Ropes 3 Strand Multiline II is a unique construction that combines filament and staple/spun polyester wrapped around a polyolefin core to produce a rope with considerably lower stretch, better wear life and superior handling characteristics.

• Color: White/Orange
• Material: Polyester Blend
• Construction: 3 Strand
• Easy to splice
• Ideal for rigging

Learn More

Just Perfect Pole Steps : JP Steps Removable utility pole and tree steps. This is the step only. These steps can replace common utility pole steps that have an upturned hook end.

Learn More

Snap hooks are recommended as they are easier for small hands, more ergonomically friendly and are permanently attached to the lobster claws. Learn More

By incorporating a rigid stem on this belay/rappel device, climbers go from full lock-off to whipping out rope in a single, smooth action. No more binding up as the device tries to free itself. The amount of friction can be easily adjusted to suit your particular need. Climbing with fat ropes, a skinny partner or on low-angle slabs? Belay with the U-Grooves and clip into the bottom hole of the XF Forge for less friction. For the ultimate control, wrap that skinny cord around the rigid stem and rappel, figure-8 style.

Learn More

Just Perfect Pole Steps : JP Steps Removable utility pole and tree steps

Learn More

This innovative, all-in-one Pulley/Auto belay for fall protection is lightweight and easy to use. Auto belay pulley Locks in either direction (right or left) while climbing up or down. Learn More

Removable climbing holds have been machined not to overlap the baseplate. Building this product is a complicated process using climbing holds intentionally designed for the baseplate and key. We recommend you purchase this fully assembled version. 

If a climbing hold overlaps the baseplate, it will not meet commercial playground standards. Other products in the industry have their climbing holds overlapping the baseplate. 

Once the base plate is attached to your wall, no tools are required to remove and reinstall the hold assembly. A removable climbing hold is ideal when your wall is not in use and you must prevent access to meet ACCT/CPSI standards. 

 

To install, screw the baseplate to the wall, insert the key/climbing hold into the top of the slot and slide the climbing hold down to the bottom of the bracket. 

 

• Plate dimensions are 4-3/4" at the widest x 6-1/2" tall.
• One rock climbing hold and bracket assembly included. 
• This product comes fully assembled and includes attachment screws.
• Insert into the slot and slide down to lock in place.
• Slide up and lift out of the slot for easy removal.
• Ten different designs, which are all jugs. 
• Large base plate to accommodate large holds and meet ASTM, ACCT, CPSI, and CSA standards.

Learn More

These patented barrel springs reduce initial impact by stopping the rider more gradually than traditional springs.

Determining how many springs you will need is easy! Simply take the incoming speed of your rider and for each mph, you need that many springs. (e.g., a 20-MPH zipline needs 20 springs for a 230-lb zipliner). 

All spring systems REQUIRE TESTING to the maximum anticipated speed and load as per ACCT. Can be completed with a minimum of 250 lb. weights, sandbags, or bagged rock salt.

These Zipline  Brakes install in minutes, NOT hours.

Made in the USA.

Each spring array includes a bumper at the beginning for trolley strikes.

Learn More

Petzl Am'D Carabiner - Add security to your climbing anchors with the Petzl Am'D Traict Locking Carabiner. Take your pick of Petzl's Screw-Lock, Ball-Lock, or Triact-Lock gate to perfectly match your preference. The Am'D Carabiner also has a snag-free keylock gate to assure it never snags on gear when you're building a solid anchor at the top of the pitch you just climbed. Learn More