Search results for: 'petzl standard rope belai'

Multiline 3-Strand Spliced Rope Zip Line Lanyards (tethers). Plastic teardrop shaped thimble on each end.

Learn More

Nail Chipper Tri-Cut Auger Bits, Typically when drilling a hole for a through bolt as used in ropes course or zip line construction, you will need to drill a hole 1/16" bigger than the bolt you are using. 5/8" bolt requires a 11/16" hole. These are all 18" long bits. 7-1/2" are available by request. Learn More

A proven winner for the ropes course. Double-back buckles on the legs and waist.

One Size Fits Most

Learn More

The original Adaptive Ropes Course harness, the ARC allows all participants to experience challenge courses and ziplines, without regard to physical ability. Designed especially for participants with physical challenges, the ARC features a thickly padded, rigid seat, with integrated chest and pelvic harnesses, secure four point attachment system and dorsal head panel, providing a safe, comfortable harness for experiencing modern ropes courses.

*ARC Spreader Bar sold separately*

Learn More

The Rescue Figure 8 is a special figure 8 for rescue situations and fast rappeling.  It has a special shap for multiple rope locking, allows rappeling with heavy loads, has a high strength, and fits a wide range of rope diameters. Available in light alloy or stainlees steel.

• Weight: 154g, 5.43oz (alloy) 451g, 15.9 oz (stainless steel)
• Material: Light alloy or stainless steel
• Strength: 40kN

Learn More

Crosby Fist Grip Cable Clamps Learn More

Stainless steel sideplates, 3"aluminum sheave, bushing, and stainless steel axle. 

 

MBS	Rope Capacity	Size	Weight	Efficiency
16000lbs	5/8"	6.5x4.25in	1.35lb	92.1%

Learn More

Stainless steel sideplates, 2" aluminum sheave, needle bearing, and stainless steel axle.

 

MBS	Rope Capacity	Size	Weight	Efficiency
8000lbs	1/2"	5x2.5in	0.5lb	90.6%

Learn More

Black anodized aluminum sideplates, 2 3/8" zinc coated steel sheave, bushing, and stainless steel axle. 

MBS	Cable/Rope Capacity	Size	Weight	Efficiency
6000lbs	5/8"	4.375x3.5in	0.75lb	91.4%

 

Learn More

Just Perfect Pole Steps : JP Step II

 

The JP Step I and JP Step II  are Pole/Tree steps and fall protection anchor in one (think integrated LEAD anchor). Installs with 5/8" x 6" lag in poles and 5/8" x 8" lag in trees for the JP I and II. The JP R uses a Specialty 4" Lag Bolt and plate that comes with it. Supports over 5,000 lbs when properly installed. A great alternative to traditional pole steps and staples.  These pole/tree steps are easily installed (about one minute). They also provide great positive climbing aids for hands, feet, and safety anchors. JP Steps for trees and poles are the best looking and safest integrated step - fall protection anchor for ropes courses, challenge courses, and zip line access.

Learn More

This rainbow para cord is ideal for lazy lines (or haul lines) on ropes courses and climbing walls, as well as general use. Kernmantle construction for high strength and low stretch. 350 lb strength rating. 1/8" (3mm).  Made in the Mexico.

Learn More

This rainbow para cord is ideal for lazy lines (or haul lines) on ropes courses and climbing walls, as well as general use. Kernmantle construction for high strength and low stretch. 350 lb strength rating. 1/8" (3mm).  Made in the Mexico.

Learn More

The Challenge harness is built for group-use activities like ropes courses, indoor and outdoor climbing as well as mountaineering. It is an adjustable unpadded harness with three auto locking buckles. A single visible attachment point, closing of the waist on the right side, and two different leg colors for ease and speed of use.

Learn More

The D4 Work/Rescue Descender features a unique and innovative cam action, which offers precise control at slow or fast speeds. The progressive cam works by way of one cam operating inside another cam. The D4 is the only ANSI certified descender on the market today.

• Weight: 655 grams (23 ounces)
• Strength: MBS 16kN (3597lbf)
• For use with single ropes from 10.5 - 11.5mm (7/16")
• Working Load Rating (WLL): 240kg (551lbs.)
• Certifications: CE EN12841, NFPA 1983, ANSI Z359

Learn More

A Super-efficient slicing tool that makes the most of its simple design and sturdy construction, the Vital Zip Knife holds a utility blade which is easily replaced once dull with a quick release of the Phillips screw holding the blade in position. The Vital Zip works well for cutting webbing and rope and to remove clothing from injured persons in rescue situations. And its feather light aspect means it can be carried along on a belt or in a kit pack without adding undue weight to your gear.

Learn More

Misty Mountain Challenge Harness – has quick adjust waist and leg buckles. Designed specifically for climbing gyms, ropes courses and challenge towers, the Challenge Harness is simple to use, safe and durable. It features a single reinforced tie-in point and pre threaded, quick adjust waist and leg loop buckles. The single tie in point, along with the quick adjust waist and leg buckles, provide for a quick set up and the durable components ensure much hard wear. Quick and convenient, the Challenge Harness is a great all around program harness.

Youth: Green tie-in point
Standard: Blue tie-in point
X-Large: Black tie-in point

Learn More

The Redirection Pulley is the first pulley of its kind for the zip line industry; lightweight, corrosion-resistant and specially engineered to be virtually resistant to snagging. Learn More

The CMI Velocity Micro Zipline trolley is a fast zip line trolley that is small and light weight. Stainless steel side plates assure long life and minimal wear. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Stainless Steel Cable clamps are ideal for use in salty and acidic environments like zip lining close to oceans or salt lake. These are durable and outlast Drop Forged clamps in harsh environments. Learn More

The HaulerBiner Compact Rescue Kit is a lightweight, compact and simple to use/deploy device. The HaulerBiner is fully rated for lifting people. The HaulerBiner has three pulley wheels incorporated into each carabiner, creating a compact and lightweight 6:1 or 7:1 (theoretical) mechanical advantage system. The HaulerBiner also has a purpose-designed progress capture cam with, an ‘on/off’ position.  The HaulerBiner utilises purpose-developed 6mm (1/4") rope, for strength and easy handling/best grip.  The kit is supplied in a two-pouch bag, for easy deployment. The HaulerBiner is load rated to 140kg (310lbs) but it has an MBS of at least 16kN/3500lbs tested as a complete system. The length of the system, when fully contracted is only 32cm (12"). EN 12278, EN 567 certifications

Learn More

Designed by top cavers for tight places in the most remote areas on earth (or under it). Surprisingly simple the new designs are comfortable to use thanks to the ergonomic grips. Learn More

The smallest and strongest knot passing pulley on the market today! With an incredible MBS of 15,000 lbs and high strength stainless steel, our knot passing pulley puts the others to shame. Learn More

Kong Furtura Chest Acscender Learn More

Yates Figure Eight Chest Harness, Great for use on zip line operations. Attachment points at waist and between shoulders. Safety attachment at rear of waist. Padded waist belt. Super easy to get on and adjust. Learn More

CMI Double Expedition Ascender, The cam is the same design as those in our now famous Ultrascenders and carries the same lifetime wear-out guarantee. Extra large handgrip opening easily accomodates gloved or mittened hands Learn More

Nylon Shock Cord consists of a stranded rubber core covered with braided fiber resulting in an elastic cord with consistent stretch and strength. The durable "bungee type" cord is covered with nylon. Learn More

They fit securely on a wide range of flange widths and beam sizes, with a built-in suspension bar that provides for close mounting. The clamp jaw design reduces flange stress by distributing the load away from the flange edge. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More