Search results for: '1/2" rapid links'

Used as spacers or supports under screw or bolt heads. Our washers are heat treated galvanized. Learn More

Width:	1.56 in
Strand Size:	1/4 to 7/16 in
Specifications:	100 ft-lb Minimum Bolt Torque
Finish:	Hot Dipped Galvanized
Length:	4 in
Material:	Steel
Clamping Bolt Size:	1/2 in
Suitable For Use With:	Loop Type Guy Dead End
Order Interval:	1
Vendor SKU:	6449
Standard & Approvals:	ARRA Compliant|Buy American Act Compliant|ASTM A153
Manufacturer:	Hubbell
Includes:	(3) Bolts
Brand:	CHANCE®
Features & Benefits:	Parallel grooves trap strand tightly without marring Each bolt has a shoulder to prevent turning while tightening

Learn More

Stainless Steel Thimbles, When the zip line wire rope is terminated with a loop, there is a risk that the wire rope can bend too tightly, especially when the loop is connected to a device that spreads the load over a relatively small area. Learn More

Cable Clamp: Crosby Wire Rope Clip Learn More

Nail Chipper Tri-Cut Auger Bits, Typically when drilling a hole for a through bolt as used in ropes course or zip line construction, you will need to drill a hole 1/16" bigger than the bolt you are using. 5/8" bolt requires a 11/16" hole. These are all 18" long bits. 7-1/2" are available by request. Learn More

Unlike the competition it is assembled using machined axles which may cost more but give the SR-71 zip trolley unparalleled structural integrity. Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

The "COBRA" cable pulley zip line trolley represents the most advanced design work using state of the art engineering techniques to build the safest and finest zip line trolley for the ropes course industry. Learn More

Nylon Shock Cord consists of a stranded rubber core covered with braided fiber resulting in an elastic cord with consistent stretch and strength. The durable "bungee type" cord is covered with nylon. Learn More

Rope thimbles protect the rope from wear whenever you have a fixed loop in the end of the rope, whether the rope is tied, spliced, or swaged. Learn More

They fit securely on a wide range of flange widths and beam sizes, with a built-in suspension bar that provides for close mounting. The clamp jaw design reduces flange stress by distributing the load away from the flange edge. Learn More

Lag Screw Lag Bolt - Galvanized, Typically used for LEAP anchors, deck constuction for zip lines and ropes courses. Hot Dipped Galvanized; Hex Head Lag Screw. 5/8" x 6" lags or 5/8" x 8" lags are recommended for Leap/Lead/Bolt hanger anchors where through bolts are not required Learn More

The Klein Haven Cable Grip is designed for use when a light, compact grip is desired and where zipline or other cable damage is not a factor. Gripping pressure of the knurled jaw s applied to ¼” of zipline cable area. Learn More

Lightness and comfort have made the METEOR helmet a signature product for climbing and mountaineering. This model has the advantage of large openings for excellent ventilation. Learn More

Thimbleye® bolts are forged in two styles, straight and bent at a 45° angle. The broad radius of the eye provides an excellent attachment point to dead-end or guy messenger wire, guy strand or formed wire grips. Learn More

Deep Cut telephone Pole Auger Bits: 24", Super long 24" Pole Auger Bits for telephone poles, utility poles, treated poles, ropes course and zip line poles. Designed for making deep cuts in utility poles, pressure treated lumber, railroad ties, and wet or frozen lumber. Learn More

Deep Cut Pole Auger Bits Learn More

The GRIGRI 2 belay device with assisted braking is designed to facilitate belay maneuvers. Learn More

Great for ropes courses, zip line, high elements, and low ropes challenge courses. Cable Clamps, sometimes called cable stops or cable clips, are tools that are used to clamp down on wire rope commonly used in industrial applications as well as in zip lining and ropes course construction. Learn More

HIT Lever hoists have a rugged contruction and a cover to protect the gear case and the brake equipment. The drop forged and heat treated alloy hooks are equipped with safety latches to ensure safety at all times. The steel handle rotates 360 degrees for operation in any posistion. The chain is made from high quality alloy steel and has been specially heat treated for high breaking stress and durability. This hoist has been tested 1.5 times its rated capacity.

• Designed for construction and industrial lifting and pulling applications.
• Rugged steel body construction, lightweight, compact and portable.
• Powder coat painted to protect against rust and corrosion.
• High Tensile alloy steel chain is heat treated for safety and low-wear.
• Shock resistant gear case and brake cover.

Learn More

A practical zip line tour trolley for professional zip line tours and canopy tours. The ultra-long design provides superior stability and travel on any zip line at any speed. Learn More

Anchors 10" 1-1/4" 96" Learn More

Stainless steel sideplates, 2" aluminum sheave, needle bearing, and stainless steel axle.

 

MBS	Rope Capacity	Size	Weight	Efficiency
8000lbs	1/2"	5x2.5in	0.5lb	90.6%

Learn More

The Head Rush Brake Trolley is a replacement for the brake trolley that came with your Head Rush zipSTOP Zip Line Brake. Please ensure that you select the correct size for your zip line cable. Learn More

GUY ANCHORS- Helix Ground Anchors : 10" x 1-1/4" x 96" Learn More

When the zip line wire rope is terminated with a loop, there is a risk that the wire rope can bend too tightly, especially when the loop is connected to a device that spreads the load over a relatively small area. Learn More

The 1/4, 5/16, and 3/8 Swaging Tools are designed for crimping copper and aluminum oval sleeves and stop sleeves on zip lines, life lines,ropes course elements. Learn More

3 Strand Import Polydacron Rope combines filament and staple/spun polyester wrapped around a polyolefin core to produce a rope with considerably lower stretch, better wear life and superior handling characteristics.

• Color: White/Red
• Material: Polyester Blend
• Construction: 3 Strand
• Easy to splice
• Ideal for Element Construction

Learn More

Teufelbergers - New England Ropes 3 Strand Multiline II is a unique construction that combines filament and staple/spun polyester wrapped around a polyolefin core to produce a rope with considerably lower stretch, better wear life and superior handling characteristics.

• Color: White/Orange
• Material: Polyester Blend
• Construction: 3 Strand
• Easy to splice
• Ideal for rigging

Learn More

Finish:	Galvanized, ASTM A-153
Material:	Steel
Width:	1-1/2 in
Length:	1/4 in
Vendor SKU:	5004
Minimum Order Qty:	1
UPC:	096359072133
Order Interval:	1
Manufacturer:	Hubbell Power
Brand:	CHANCE®
Features & Benefits:	Guy hook restricts guy wire from creeping down pole in wrapped strand guy applications. Can also be used as guy attachment, when used in compliance with deadend manufacturer's requirements. Hooks should be installed under head of bolt for maximum bolt shear strength.

Learn More

The Head Rush Brake Trolley is a replacement for the brake trolley that came with your zipSTOP Zip Line Brake. Learn More

Our Machine Bolts are hot dip galvanized, forged steel, quenched and tempered and are sold with hex nuts attached. Round or square washers and lock washers can be added separately. Learn More

Our Galvanized Aircraft Zip Lining Cable is made in accordance with Federal Specification RR-W-410D, meeting the dimensional and strength requirements of MIL-W-83420D. Learn More

GUY ANCHORS- Helix Ground Anchors : 8" x 1" x 66" Learn More

GUY ANCHORS- Helix Ground Anchors, Multiple sizes and capacities allow precise designs for the adventure and zip line industry. There may be one or multiple guywires that can be resisted by one or multiple guy wire anchors, dictated by design and load requirements. Learn More

RSRP431 R-ALF Rescue Hauler Pulley- 2 Way Auto Locking Approved standards CE 0120 ANSI Z359 :4: 2007

 The R-ALF Pulley is the latest innovation in Accessability, Rescue, Confined Space working and Work Suspension Systems. The R-ALF Pulley has an over-speed brake built in so that the Pulley will lock on and hold when a fall occurs. The load rated Becket Eye on the R-ALF means that it can be used in combination with Prussic Pulleys to create a 3: 1 or 5: 1 Mechanical Advantage System. The unique design of the R-ALF (design patent applied for), means that an internal brake is not required and therefore it is capable of several thousand cycles and many arrests (minimum 12 monthly service intervals apply). Weight (grams) 1200 Weight (ounces) 43 Rope diameter range (mm) Approved 11mm EN1891-A Ropes Only Number of persons 2

Learn More