Search results for: 'rope course'and select 1 0waitfor design 0 0 0'

Nylon Shock Cord consists of a stranded rubber core covered with braided fiber resulting in an elastic cord with consistent stretch and strength. The durable "bungee type" cord is covered with nylon. Learn More

The RC-800 Wire Rope Cutters are used for cutting 1/16 to 5/8 inch cable. Learn More

Designed for use on Challenge ropes course/Zip Lining traverses, on cable or rope. Super strong with a 10,000 rating and a sheathed back up bolt. Stainless steel sides make this cable pulley bomb proof. Learn More

Nail Chipper Tri-Cut Auger Bits, Typically when drilling a hole for a through bolt as used in ropes course or zip line construction, you will need to drill a hole 1/16" bigger than the bolt you are using. 5/8" bolt requires a 11/16" hole. These are all 18" long bits. 7-1/2" are available by request. Learn More

Get the best selection and best quality of Cargo Climbing and Ropes Course Nets. Our nets and ladder are constructed of high quality materials and even higher quality workmanship. Learn More

Purple Anodized Aluminum sideplates, 1 1/4" Aluminum sheave, Bushing, and Stainless Steel axle. Learn More

CMC Rescue's All-Weather Rope Log contains 20 rope log forms on heavy, Rite-in-the-Rain paper. Ample space is provided to document critical lifeline information and log use and inspection. Learn More

Ropes Course Zip Line Staples, Staples are the preferred way access ropes challenge course elements and zip line platforms: easy to install, easy to inspect, and easy to climb. If properly installed, the 8" staples can perform as fall protection anchors Learn More

We offer three different style of pilot auger bits for 1/2" lags for ropes course decks, zip line decks and general deck construction for 1/2" & 5/8" lag bolts Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

GUY ANCHORS- Helix Ground Anchors, Multiple sizes and capacities allow precise designs for the adventure and zip line industry. There may be one or multiple guywires that can be resisted by one or multiple guy wire anchors, dictated by design and load requirements. Learn More

Red Anodized Aluminum sideplates, 2 3/8" Glass-filled Celcon sheave, n/a, and Stainless Steel axle. The original rope pulley! Durable design, great action, light weight and easy to use. Learn More

Anchors 10" 1-1/4" 96" Learn More

The SEQUOIA is a seat harness for tree care. It is designed for the arborist's comfort. The extra-wide, semi-rigid waist belt and leg loops give excellent support. Learn More

Our enhancements include adjustable spring tension, a reversible cable and pin, and "mud vents" to help prevent dirt caked on rope from degrading ascender performance. Learn More

Deep Cut telephone Pole Auger Bits: 24", Super long 24" Pole Auger Bits for telephone poles, utility poles, treated poles, ropes course and zip line poles. Designed for making deep cuts in utility poles, pressure treated lumber, railroad ties, and wet or frozen lumber. Learn More

Write, type, or stamp information on the ¾ x 1 inch white area. Clear self-laminating portion wraps around to protect writing. Learn More

The 5.4 mm V-TX Cord is the ultra-lightweight, super low-stretch addition to our High Tenacity Cord series. Learn More

Serving Sleeves, These are usually in a 1x7 configuration: 1 bundle of 7 strands. Cable used in ropes courses and zip lines is usually 7x19 or 6x24: Much more flexible Learn More

This manual rescue belay can be used as a self belay or with a belayer. The side plates and drum are made from heat treated 6061 T6 Aluminum while the two stainless steel pins keep the rope seperated as it is reaved around the drum. Drum is Aircraft Hard Anodized for extended wear which cost more but makes for a superior product. Learn More

The CORAX is the versatile harness par excellence: easy to use and comfortable, it is designed for rock climbing, mountaineering or via ferrata. Learn More

Petzl Gemini is a double Prusik pulley with moving side plates designed for technical hauling systems and raising heavy loads. Prusik pulleys are designed to be used with a Prusik hitch, making for a lightweight progress capture system. Learn More

High strength in a compact design. Stainless Steel sideplates, 2 3/8" Aluminum sheave, Bearing, and Stainless Steel axle. Learn More

Dry treatment makes the rope more resistant to water, dirt and abrasion; handling, grip and other characteristics are retained longer in cold, wet conditions. Learn More

Slices rope like Butter! This fast and efficient unit has a hot blade which cleanly cuts through rope and webbing in seconds. Learn More

The Ascension Ascender by Petzl is the benchmark for handled ascenders and has been refined to provide greater comfort; efficiency, ease of use. Learn More

UltraSonic Finish: the core and the sheath are bonded together at the rope ends by an ultrasonic process called UltraSonic Finish; gives greater durability and avoids frayed ends. Learn More

This electric handheld unit cuts and fuses the ends of polyester and nylon ropes and webbing. Easy to use and long lasting blades. heats up when trigger is pulled and cools when released. Learn More

GUY ANCHORS- Helix Ground Anchors : 8" x 1" x 66" Learn More

A step up in strength and durability from the RP101 rope pulley. Black Anodized Aluminum sideplates, 2 3/8" Aluminum sheave, Bushing, and Stainless Steel axle. A great all around rope pulley. Learn More

Mailion Rapid Links (aka "Rapides" or "Quick-Links") are steel screw-links designed for fastening lengths of chain together on ropes courses and zip lining. They provide critical connections for trolleys, balay devices, cables and cable hardware on a zip line. Learn More

Designed for rescue, it is great for portable ropes courses, ski & mountain rescue, tyrolean back ups, rescue kits, Rescue training programs, and hauling up access nets and ladders to challenge courses and climbing towers. Learn More

Shoulder Eye Screw Lag, Use for connecting hand lines, spiders webs to trees, etc. on challenge courses. Do not use in life support applications. Also used when wrapping cable around a tree. Learn More

The Y Tail - Participant Ropes Course Lanyard is manufactured from 1/2" high quality US manufactured PolyDacron 3-strand rope. The lanyard has a loop for girth hitch attachment to the harness and two ANSI rated double-locking snap hooks for connection to the lifeline (belay cable). Lanyards are adjustable from 4' (48") to 6'5" (77").

Learn More

Just Perfect Pole Steps : JP Steps Removable utility pole and tree steps. This is the step only. These steps can replace common utility pole steps that have an upturned hook end.

Learn More