Search results for: 'cm 4 inch heavy duty stainless sterl pu'

Hot Dip galvanized steel. End fittings are Quenched and Tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 5/8" and pins and cotters on 3/4" sizes. Learn More

Cable Clamp: Crosby Wire Rope Clip Learn More

A simple way to reinforce the proper use of auto belay devices and minimize risk from climbing error.

Learn More

Width:	1.56 in
Strand Size:	1/4 to 7/16 in
Specifications:	100 ft-lb Minimum Bolt Torque
Finish:	Hot Dipped Galvanized
Length:	4 in
Material:	Steel
Clamping Bolt Size:	1/2 in
Suitable For Use With:	Loop Type Guy Dead End
Order Interval:	1
Vendor SKU:	6449
Standard & Approvals:	ARRA Compliant|Buy American Act Compliant|ASTM A153
Manufacturer:	Hubbell
Includes:	(3) Bolts
Brand:	CHANCE®
Features & Benefits:	Parallel grooves trap strand tightly without marring Each bolt has a shoulder to prevent turning while tightening

Learn More

High strength in a compact design. Stainless Steel sideplates, 2 3/8" Aluminum sheave, Bearing, and Stainless Steel axle. Learn More

Nylon Shock Cord consists of a stranded rubber core covered with braided fiber resulting in an elastic cord with consistent stretch and strength. The durable "bungee type" cord is covered with nylon. Learn More

Nut Eye bolts are the main bolts used in ropes challenge course and zip line construction. Zipline and other cables are terminated to the eye bolt around a thimble to prevent cable deformation at the turn back. Learn More

Nail Chipper Tri-Cut Auger Bits, Typically when drilling a hole for a through bolt as used in ropes course or zip line construction, you will need to drill a hole 1/16" bigger than the bolt you are using. 5/8" bolt requires a 11/16" hole. These are all 18" long bits. 7-1/2" are available by request. Learn More

Ropes Course Zip Line Staples, Staples are the preferred way access ropes challenge course elements and zip line platforms: easy to install, easy to inspect, and easy to climb. If properly installed, the 8" staples can perform as fall protection anchors Learn More

This Cable Spooler is Made of sturdy heavy-duty steel tubing and folds for easy storage and had a tough, durable finish.

• Maximum reel width: 18";
• Height from floor to rod: 13"
• Weight: 7.5lbs;
• Holds: 200lbs.

Learn More

Zipline Cable Ferrule - Zinc Plated, Two ferrules are required for life support and ziplining applications (ACCT Standards). The extra ferrule serves as a backup in case of primary ferrule failure due to defects or improper swaging. A 12 ton crimper/compression tool is required for 1/4" - 1/2" ferrules Learn More

Headwall Universal Harness, The headwall is a 'double back' harness. This style takes longer to put on but will not loosen over time as parachute buckle harnesses can do Learn More

Write, type, or stamp information on the ¾ x 1 inch white area. Clear self-laminating portion wraps around to protect writing. Learn More

Klein Tools' Lineman's Wrenches are forged from special bar steel and heat-treated for durability and long life. These wrenches are designed for use on heavy three-bolt guy clamps where clearance is limited. Each end has two different size openings, plus a hole at the larger end for turning-in standard pole steps.

• Forged from special bar steel and heat-treated for long life
• Each end has two different size openings
• Small end has 5/8-Inch and 13/16-Inch openings; large end features 29/32-Inch and 1-3/32-Inch openings
• Hole is provided at larger end for turning-in standard pole steps
• Made in USA
• Wrench is suited for use on the heavy three-bolt guy clamps on which clearance is limited
• Dark blue painted finish

Learn More

Anodized aluminum sideplates, 2 3/4" aluminum sheave, ball bearing and stainless steel axle. Learn More

Purple Anodized Aluminum sideplates, 1 1/4" Aluminum sheave, Bushing, and Stainless Steel axle. Learn More

Great for ropes courses, zip line, high elements, and low ropes challenge courses. Cable Clamps, sometimes called cable stops or cable clips, are tools that are used to clamp down on wire rope commonly used in industrial applications as well as in zip lining and ropes course construction. Learn More

Used as spacers or supports under screw or bolt heads. Our washers are heat treated galvanized. Learn More

The RC-800 Wire Rope Cutters are used for cutting 1/16 to 5/8 inch cable. Learn More

The Head Rush Brake Trolley is a replacement for the brake trolley that came with your zipSTOP Zip Line Brake. Learn More

STARGATE SRD -Shear Reduction Device, The 4" aluminum sheave is hard anodized and pared from any excess weight, while the stainless frame surrounds the sheave with minimal surface contact Learn More

The smallest and strongest knot passing pulley on the market today! With an incredible MBS of 15,000 lbs and high strength stainless steel, our knot passing pulley puts the others to shame. Learn More

Deep Cut telephone Pole Auger Bits: 24", Super long 24" Pole Auger Bits for telephone poles, utility poles, treated poles, ropes course and zip line poles. Designed for making deep cuts in utility poles, pressure treated lumber, railroad ties, and wet or frozen lumber. Learn More

Deep Cut Pole Auger Bits Learn More

Petzl Gemini is a double Prusik pulley with moving side plates designed for technical hauling systems and raising heavy loads. Prusik pulleys are designed to be used with a Prusik hitch, making for a lightweight progress capture system. Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

Serving Sleeves, These are usually in a 1x7 configuration: 1 bundle of 7 strands. Cable used in ropes courses and zip lines is usually 7x19 or 6x24: Much more flexible Learn More

The ETD - Ropes Course Rescue Bag is filled with essential items to preform a aerial rescue. If there are extra items you require for you rescue bag simply order them separately and toss them in you bag.

Contents:

• 1 - Medium Orange Rope Bag w/Rope History Record - 150'
• 1- 7/16" x 100', 120' or 150' KMIII Orange Static Rope
• 6' - 5mm Tech Cord for Tying Prusik 
• 1 - Pair EMT Shears 
• 1 - Aluminum Rescue 8  
• 4 - Steel Screw-Gate Big D Carabiners 
• 1 - BFD/ATC (Belay Friction Device)
• 1 - 5 Step Easy Step Aider
• 1 - Set Fixed Length 1" Heavy Duty Webbing Lobster Claws w/Zorber & Hooks

Learn More

A practical zip line tour trolley for professional zip line tours and canopy tours. The ultra-long design provides superior stability and travel on any zip line at any speed. Learn More

Lock washers are a critical component to through bolts on wood poles. Pole shrinkage mandates the use of double coil lock washers to keep pressure on the nut and bolt to prevent loosening. Learn More

The Head Rush zipSTOP Braking System. This zipSTOP Brake Trolley is engineered for a fine balance. It is able to handle the abuse of heavy impact collisions, yet light enough to increase the odds of reliable reset. Learn More

Teufelbergers - New England Ropes 3 Strand Multiline II is a unique construction that combines filament and staple/spun polyester wrapped around a polyolefin core to produce a rope with considerably lower stretch, better wear life and superior handling characteristics.

• Color: White/Orange
• Material: Polyester Blend
• Construction: 3 Strand
• Easy to splice
• Ideal for rigging

Learn More

3 Strand Import Polydacron Rope combines filament and staple/spun polyester wrapped around a polyolefin core to produce a rope with considerably lower stretch, better wear life and superior handling characteristics.

• Color: White/Red
• Material: Polyester Blend
• Construction: 3 Strand
• Easy to splice
• Ideal for Element Construction

Learn More

CMI Twin Expedition Arborist Ascender, The Twin Expedition is the first single-handled dual ascender designed to meet the needs of industry leading arborist professionals. The EXPTWIN easily accommodates three rope techniques - 2:1 doubled rope technique (DdRT), 1:1 single rope technique (SRT), and 1:1 twin line ascent (DbRT). Learn More

The Klein Haven Cable Grip is designed for use when a light, compact grip is desired and where zipline or other cable damage is not a factor. Gripping pressure of the knurled jaw s applied to ¼” of zipline cable area. Learn More

CMI Double Expedition Ascender, The cam is the same design as those in our now famous Ultrascenders and carries the same lifetime wear-out guarantee. Extra large handgrip opening easily accomodates gloved or mittened hands Learn More