Search results for: 'new england rescu line'

Multiline 3-Strand Spliced Rope Zip Line Lanyards (tethers). Plastic teardrop shaped thimble on each end.

Learn More

The KAA is a self contained mechanical advantage system for tensioning lines or lifting people during rescues. In addition, as the KAA is certified to EN 354, it can be used for workplace stabilization, as a restraint system (open/closed), and for controlled lowering. Its strap-based construction makes it the most compact and lightweight system on the market. Depending on the orientation, it offers a 4:1 or 5:1 lifting ratio with an efficiency of 91%. The KAA is packaged compactly and ready for immediate use, so that no valuable time is lost when it is required. A swivel is provided at each end to prevent the system from twisting. The hand lever on the draw cord makes it easier to pull and can also be used as a lowering lever.

 

Weight: 500g (1.1lbs)

MBS: 22kN

Certification: EN 354

Efficiency: 91%

• Compact and lightweight due to strap-based construction
• 4:1 or 5:1 mechanical advantage
• Can be set up in seconds
• Swivels on both ends

Learn More

Stainless Steel Thimbles, When the zip line wire rope is terminated with a loop, there is a risk that the wire rope can bend too tightly, especially when the loop is connected to a device that spreads the load over a relatively small area. Learn More

Just Perfect Pole Steps : JP Step II

 

The JP Step I and JP Step II  are Pole/Tree steps and fall protection anchor in one (think integrated LEAD anchor). Installs with 5/8" x 6" lag in poles and 5/8" x 8" lag in trees for the JP I and II. The JP R uses a Specialty 4" Lag Bolt and plate that comes with it. Supports over 5,000 lbs when properly installed. A great alternative to traditional pole steps and staples.  These pole/tree steps are easily installed (about one minute). They also provide great positive climbing aids for hands, feet, and safety anchors. JP Steps for trees and poles are the best looking and safest integrated step - fall protection anchor for ropes courses, challenge courses, and zip line access.

Learn More

The Head Rush Impact Trolley Sheave Replacement Kit allows you to replace your Impact Trolley sheave assembly should they wear out or become damaged. Learn More

The Impact Surface Replacement Kit allows you to replace the Impact Surface on your Impact Trolley should it wear out or become damaged. Learn More

The Head Rush TRUBLUE XL Auto Belay is fitted with a webbing that can be replaced in the field by the owner using the Replacement Webbing. Learn More

Haul kit for pickoffs, making a releasable anchor, or tensioning a system, thanks to its 4:1 mechanical advantage and excellent efficiency (sheaves with sealed ball bearings). Learn More

The Impact Trolley Cover Plate Replacement Kit allows you to replace the Cover Plates on your Impact Trolley should they wear, get misplaced or damaged Learn More

The Zippey Trolley is bi-directional, so there’s no wrong way to fit it. Zippey offers a one handed action with either a single or double locking mechanism for increased safety.

Zippey has a speed rating of 60mph (90kph), which is based on the use of the same high spec deep groove, double row ball bearings, as used in our Zipspeed range. The expected life of the bearings should be more than 1000 miles (1500km).

Accessories available for the Zippey Trolleys

ARC – Anti Roll Back Cam. This innovative add on solves many of the issues associated with modern zip lines. Riders who reach the egress platform can roll back out onto the line requiring staff intervention. The ARC ensures that the rider remains in position over the egress platform by camming against the zip line cable maintaining their position.

Handle Accessory – There is now an available handle accessory for the Zippey making it possible for riders to ‘steer’ into the arrival station.

Learn More

The Ascension Ascender by Petzl is the benchmark for handled ascenders and has been refined to provide greater comfort; efficiency, ease of use. Learn More

CIFA: 10286 Klein Tools 809-36 hammer is designed and created to strike through jobsite challenges. Engineered with the professional in mind, each tool is job-matched to fit the task at hand. Features: Designed for pole-line work   Rugged and well-balanced, with the weight to drive lag bolts   Forged, tempered-steel head for use in tight areas   Identical faces with round-crown driving surface and beveled edges

Learn More

Petzl Pandion Harness, Adjustable leg loops allow size to be adjusted depending on comfort desired or layers of clothing worn and permit the harness to be put on when wearing skis or crampons Learn More

The Head Rush Bump Stop is considered a sacrificial part that is designed to wear out over time Learn More

GUY ANCHORS- Helix Ground Anchors : 4" x 3/4" x 54" Learn More

GUY ANCHORS- Helix Ground Anchors : 10" x 1-1/4" x 96" Learn More

GUY ANCHORS- Helix Ground Anchors : 8" x 1" x 66" Learn More

GUY ANCHORS- Helix Ground Anchors : 6" x 3/4" x 66" Learn More

Aspir Adjustable Harness, Its low bulk and large range of adjustability also make it great for mountaineering and glacier travel. A great harness too for via ferrata and adventure parks. Learn More

Deep Cut Pole Auger Bits Learn More

Zipline Cable Ferrule - Zinc Plated, Two ferrules are required for life support and ziplining applications (ACCT Standards). The extra ferrule serves as a backup in case of primary ferrule failure due to defects or improper swaging. A 12 ton crimper/compression tool is required for 1/4" - 1/2" ferrules Learn More

EYE NUTS and EYELETS, Eyelets, also known as Bolt Eyes, are used under the head or nut of a bolt. All are compatible with the strength of the bolts used with them. Learn More

Nylon Shock Cord consists of a stranded rubber core covered with braided fiber resulting in an elastic cord with consistent stretch and strength. The durable "bungee type" cord is covered with nylon. Learn More

Used as spacers or supports under screw or bolt heads. Our washers are heat treated galvanized. Learn More

Adjama Climbing Harness, Lightweight and very flexible, thanks to the Delta System leg loop front panels and small dimension leg buckles. Learn More

Lock washers are a critical component to through bolts on wood poles. Pole shrinkage mandates the use of double coil lock washers to keep pressure on the nut and bolt to prevent loosening. Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

Ferrules must be properly crimped to achieve holding strength. Properly swaged ferrules can hold 90% of cable strength. Two ferrules are required for life support and ziplining applications (ACCT Standards). Learn More

Yellow 8' Guy Marker - Guy Guard Learn More

Our Machine Bolts are hot dip galvanized, forged steel, quenched and tempered and are sold with hex nuts attached. Round or square washers and lock washers can be added separately. Learn More

Petzl Basic Ascender, The BASIC is a compact ascender that offers excellent grip for rope ascents. The lower attachment hole is large enough to hold the carabiners for the lanyard and the footloop. Learn More

The Finesse climbing/zipline harness is designed specifically for women. It is slightly narrower and lighter than our Silhouette harness, making it a great choice for single pitch or sport climbing applications or even zipline runs. Learn More

Rock Exotica enForcer Load Cell is a compact aluminum load cell that measures force up to 20 kN. Utilizing two sampling modes, the Enforcer is able to monitor systems, and log drop testing in high resolution. Learn More

Certified according to EN 17109 (class D)! The Smart Belay X is a redesign of our legendary Smart Belay - now with innovative magnetic technology for continuous safety and maximum freedom of movement in your high ropes course. Certified according to EN 17109 (class D).

 

• Quick registration and effective management thanks to RFID technology
• communicating, interconnected pulley carabiners prevent accidental detachment from the safety cable
• safety lock with magnet technology for maximum security and protection against careless use
• intuitive operation even for children
• steel pulleys integrated in the carabiner for use on zip lines replace the double pulley
• PILOT BAR minimizes the risk of strangulation and provides support for difficult elements in the course
• modular system allows the use of different connectors and different lengths of tie-in loops
• quick and easy evacuation made possible by opener or steel carabiner (not included in delivery)
• SBX HOLSTER included

Learn More

Just Perfect Pole Steps : JP Steps Removable utility pole and tree steps. This is the step only. These steps can replace common utility pole steps that have an upturned hook end.

Learn More