Search results for: 'and ryzentm 7 91'

We offer three different style of pilot auger bits for 1/2" lags for ropes course decks, zip line decks and general deck construction for 1/2" & 5/8" lag bolts Learn More

A superior handling rescue rope,Teufelberger (New England) Ropes KM III static, kernmantle rope features a composite construction of nylon and polyester fibers. Learn More

Serving Sleeves, These are usually in a 1x7 configuration: 1 bundle of 7 strands. Cable used in ropes courses and zip lines is usually 7x19 or 6x24: Much more flexible Learn More

CMI Ultrabrake, Designed for hard use and maximum UV resistance, the material has a low friction coefficient and is self-lubricating with a non-adherent surface. Learn More

Rope thimbles protect the rope from wear whenever you have a fixed loop in the end of the rope, whether the rope is tied, spliced, or swaged. Learn More

Width:	1.56 in
Strand Size:	1/4 to 7/16 in
Specifications:	100 ft-lb Minimum Bolt Torque
Finish:	Hot Dipped Galvanized
Length:	4 in
Material:	Steel
Clamping Bolt Size:	1/2 in
Suitable For Use With:	Loop Type Guy Dead End
Order Interval:	1
Vendor SKU:	6449
Standard & Approvals:	ARRA Compliant|Buy American Act Compliant|ASTM A153
Manufacturer:	Hubbell
Includes:	(3) Bolts
Brand:	CHANCE®
Features & Benefits:	Parallel grooves trap strand tightly without marring Each bolt has a shoulder to prevent turning while tightening

Learn More

Cable Clamp: Crosby Wire Rope Clip Learn More

Nail Chipper Tri-Cut Auger Bits, Typically when drilling a hole for a through bolt as used in ropes course or zip line construction, you will need to drill a hole 1/16" bigger than the bolt you are using. 5/8" bolt requires a 11/16" hole. These are all 18" long bits. 7-1/2" are available by request. Learn More

When the zip line wire rope is terminated with a loop, there is a risk that the wire rope can bend too tightly, especially when the loop is connected to a device that spreads the load over a relatively small area. Learn More

Deep Cut telephone Pole Auger Bits: 24", Super long 24" Pole Auger Bits for telephone poles, utility poles, treated poles, ropes course and zip line poles. Designed for making deep cuts in utility poles, pressure treated lumber, railroad ties, and wet or frozen lumber. Learn More

Deep Cut Pole Auger Bits Learn More

Learn More

Learn More

Ultra-compact and extremely lightweight pulley designed for daily tasks or on-site rescue. Learn More

Compact pulley offering a lightweight solution for setting up progress capture systems. Learn More

Learn More

Petzl Gemini is a double Prusik pulley with moving side plates designed for technical hauling systems and raising heavy loads. Prusik pulleys are designed to be used with a Prusik hitch, making for a lightweight progress capture system. Learn More

Gripple Ropes Course Cable Connector, Learn More

Double pulley designed for use with the JAG TRAXION double progress capture pulley to make a 4:1 haul system. Sheaves mounted on sealed ball bearings for excellent efficiency. Learn More

MICRO TRAXION is an ultra-compact, extremely light progress capture pulley that is exceptionally efficient. The cam can be locked in open position so the device can be used as a simple pulley. Learn More

Double progress capture pulley designed for use with the JAG double pulley to make a 4:1 haul system. Sheaves mounted on sealed ball bearings for excellent efficiency. Learn More

The KAA is a self contained mechanical advantage system for tensioning lines or lifting people during rescues. In addition, as the KAA is certified to EN 354, it can be used for workplace stabilization, as a restraint system (open/closed), and for controlled lowering. Its strap-based construction makes it the most compact and lightweight system on the market. Depending on the orientation, it offers a 4:1 or 5:1 lifting ratio with an efficiency of 91%. The KAA is packaged compactly and ready for immediate use, so that no valuable time is lost when it is required. A swivel is provided at each end to prevent the system from twisting. The hand lever on the draw cord makes it easier to pull and can also be used as a lowering lever.

 

Weight: 500g (1.1lbs)

MBS: 22kN

Certification: EN 354

Efficiency: 91%

• Compact and lightweight due to strap-based construction
• 4:1 or 5:1 mechanical advantage
• Can be set up in seconds
• Swivels on both ends

Learn More

Haul kit for pickoffs, making a releasable anchor, or tensioning a system, thanks to its 4:1 mechanical advantage and excellent efficiency (sheaves with sealed ball bearings). Learn More

Lag Screw Lag Bolt - Galvanized, Typically used for LEAP anchors, deck constuction for zip lines and ropes courses. Hot Dipped Galvanized; Hex Head Lag Screw. 5/8" x 6" lags or 5/8" x 8" lags are recommended for Leap/Lead/Bolt hanger anchors where through bolts are not required Learn More

Rugged and compact, the OXAN carabiner is particularly suited for use in difficult conditions where weight is not an issue: setting fixed anchors, connecting to metal structures... Learn More

Apex is the workhorse of the MAXIM® product line. Designed for big wall and trad climbing or for working projects and developing routes, Apex makes an excellent rope for challenge courses and fall protection for safety personnel. Learn More

The 20 g barrier has been broken! The Nineteen G is the lightest carabiner in the world – and makes no compromises on strength. Learn More

CMI "Beast" Tour Trolley Pulley, Designed for the fast lane of zip line tours, this trolley features a front bumper, reinforced 'crimped' side bars and forward facing design with drop down handles. Learn More

The D4 Work/Rescue Descender features a unique and innovative cam action, which offers precise control at slow or fast speeds. The progressive cam works by way of one cam operating inside another cam. The D4 is the only ANSI certified descender on the market today.

• Weight: 655 grams (23 ounces)
• Strength: MBS 16kN (3597lbf)
• For use with single ropes from 10.5 - 11.5mm (7/16")
• Working Load Rating (WLL): 240kg (551lbs.)
• Certifications: CE EN12841, NFPA 1983, ANSI Z359

Learn More

CMC now offers the standard utility scissors with titanium bonded blades. Using a patented process, titanium is bonded to a stainless steel core to produce a sharper, more corrosion resistant, longer lasting edge. Learn More

Steel carabiners are referred in ropes course, zip line, and cable applications. Learn More

Pulley carabiner, available in versions with or without TRIACT-LOCK locking system. Learn More

This Large Twistlock carabiner has a key gate opening for smooth clips and unclips. No more snagging on ziplining harnesses, cables, gear or bolts. Learn More

This innovative, all-in-one Pulley/Auto belay for fall protection is lightweight and easy to use. Auto belay pulley Locks in either direction (right or left) while climbing up or down. Learn More

Ultra lightweight compact pulley designed for a variety of uses. Learn More

When closed with a wrench, this steel quick link becomes a semi-permanent anchor ring. Learn More