Cable Clamp: Crosby Wire Rope Clip1

More Views

  • Cable Clamp: Crosby Wire Rope Clip1
  • Cable Clamp: Crosby Wire Rope Clip2
  • Cable Clamp: Crosby Wire Rope Clip5
  • Cable Clamp: Crosby Wire Rope Clip6

Cable Clamp: Crosby Wire Rope Clip

Be the first to review this product

Availability: In stock

$6.00

* Required Fields

$6.00

Details

CROSBY CABLE CLAMP WIRE ROPE CLIP

Crosby Cable Clamps are great for ropes courses, zip line, high elements, and low ropes challenge courses. Cable Clamps, sometimes called cable stops or cable clips, are tools that are used to clamp down on wire rope commonly used in industrial applications as well as in zip lining and ropes course construction.

Each base has a Product Identification Code (PIC) for material traceability, the name CROSBY or CG,
and a size forged into it.
• Based on the catalog breaking strength of wire rope, Crosby wire rope clips have an efficiency rating
of 80% for 1/8” - 7/8” sizes, and 90% for sizes 1” through 3-1/2”.
• Entire Clip-Galvanized to resist corrosive and rusting action.
• Sizes 1/8” through 2-1/2” and 3” have forged bases.
• All Clips are individually bagged or tagged with proper application instructions and
warning information.
• Clip sizes up through 1-1/2” have rolled threads.
• Meets or exceeds all requirements of ASME B30.26 including identification, ductility, design factor,
proof load and temperature requirements. Importantly, these wire rope clips meet other critical
performance requirements including fatigue life, impact properties and material traceability, not
addressed by ASME B30.26.
• Look for the Red-U-Bolt®, your assurance of Genuine Crosby Clips.

ITEM

SIZE

 

PRICE

CROSBY CABLE CLAMP 1/4" $ 5.00
CROSBY CABLE CLAMP 5/16" $ 5.35
CROSBY CABLE CLAMP 3/8" $ 5.50
CROSBY CABLE CLAMP 1/2" $ 8.40
CROSBY CABLE CLAMP 5/8" $ 10.60
CROSBY CABLE CLAMP 7/8" $ 19.40
CROSBY CABLE CLAMP 1" $ 22.40

 

     WARNING
  • Failure to read, understand, and follow these instructions may cause death or serious injury.
  • Read and understand these instructions before using clips.
  • Match the same size clip to the same size wire rope.
  • Prepare wire rope end termination only as instructed.
  • Do not use with plastic coated wire rope.
  • Apply first load to test the assembly.
    This load should be of equal or greater weight than loads expected
    in use.  Next, check and retighten nuts to recommended torque
    (See Table 1, this page).

 

Critical Application Information
Efficiency ratings for wire rope end terminations are based upon the catalog breaking strength of wire rope. The efficiency rating of a properly prepared loop or thimble eye termination for clip sizes 1/8" through 7/8" is 80%. For sizes 1" thru 3-1/2" it is 90%.
The number of clips shown (see Table 1 ) is based upon using RRL or RLL wire rope, 6 x 19 or 6 x 37 Class, FC or IWRC; IPS or XIP. If Seale construction or similar large outer wire type construction in the 6 x 19 Class is to be used for sizes 1 inch and larger, add one additional clip. If a pulley (sheave) is used for turning back the wire rope, add one additional clip.
The number of clips shown also applies to rotation - resistant RRL wire rope, 8 x 19 Class, IPS, XIP, sizes 1-1/2 inch and smaller; and to rotation-resistant RRL wire rope, 19 x 7 Class, IPS, XIP, sizes 1-3/4 inch and smaller.
For other classes of wire rope not mentioned above, we recommend contacting Crosby Engineering at
(918) 834-4611 to ensure the desired efficiency rating.
For elevator, personnel hoist, and scaffold applications, refer to ANSI A17.1 and ANSI A10.4. These standards do not recommend U-Bolt style wire rope clip terminations. The style wire rope termination used for any application is the obligation of the user.
For OSHA (Construction) applications, see OSHA 1926.251.
Table 1
Clip
Size
(Inches)
Rope
Size
(Inches)
Minimum
No.
of Clips
Amount of Rope
to Turn Back
in Inches
Torque
in
Ft. Lbs.
1/8 1/8 2 3-1/4 4.5
3/16 3/16 2 3-3/4 7.5
1/4 1/4 2 4-3/4 15
5/16 5/16 2 5-1/4 30
3/8 3/8 2 6-1/2 45
7/16 7/16 2 7 65
1/2 1/2 3 11-1/2 65
9/16 9/16 3 12 95
5/8 5/8 3 12 95
3/4 3/4 4 18 130
7/8 7/8 4 19 225
1 1 5 26 225
1-1/8 1-1/8 6 34 225
1-1/4 1-1/4 7 44 360
1-3/8 1-3/8 7 44 360
1-1/2 1-1/2 8 54 360
1-5/8 1-5/8 8 58 430
1-3/4 1-3/4 8 61 590
2 2 8 71 750
2-1/4 2-1/4 8 73 750
2-1/2 2-1/2 9 84 750
2-3/4 2-3/4 10 100 750
3 3 10 106 1200
3-1/2 3-1/2 12 149 1200
If a pulley (sheave) is used for turning back the wire rope, add one additional clip.
If a greater number of clips are used than shown in the table, the amount of turnback should be increased proportionately.

*The tightening torque values shown are based upon the threads being clean, dry, and free of lubrication.

Installation Instructions

Step 1.  Refer to Table 1 (below left) in following these instructions. Turn back specified amount of rope from thimble or loop. Apply first clip one base width from dead end of rope. Apply U-Bolt over dead end of wire rope - live end rests in saddle (Never saddle a dead horse!) Tighten nuts evenly, alternate from one nut to the other until reaching the recommended torque.
Step 2.  When two clips are required, apply the second clip as near the loop or thimble as possible. Tighten nuts evenly, alternating until reaching the recommended torque.  When more than two clips are required, apply the second clip as near the loop or thimble as possible, turn nuts on second clip firmly, but do not tighten.  Proceed to Step 3.
Step 3.  When three or more clips are required, space additional clips equally between first two - take up rope slack - tighten nuts on each U-Bolt evenly, alternating from one nut to the other until reaching recommended torque.
Figure 4.  If a pulley (Sheave) is used, in place of a thimble add one additional clip. Clip spacing should be as shown.
Wire Rope Splicing Procedures:
Figure 5. The preferred method of splicing two wire ropes together is to use interlocking turnback eyes with himbles, using the recommended number of clips on each eye (See Figure 1).
Figure 6.  An alternate method is to use twice the number of clips as used for a turnback termination. The rope ends are placed parallel to each other, overlapping by twice the turnback amount shown in the application instructions. The minimum number of clips should be installed on each dead end (See Figure 2).  Spacing, installation torque, and other instructions still apply.
IMPORTANT
Apply first load to test the assembly. This load should be of equal or greater weight than loads expected in use.
Next, check and retighten nuts to recommended torque.
In accordance with good rigging and maintenance practices, the wire rope end termination should be inspected periodically for wear, abuse, and general adequacy.

 

 

 

 

 

 

Additional Information

Country of Manufacture
Manufacturer No

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.